Whirlpool Dishwasher FAE4 or F10E4: Diverter Valve Position Error
The control cannot confirm where the diverter valve sits when FAE4, or F10E4 on some displays, appears on a Whirlpool built-in dishwasher such as the WDT730PAHZ. The cycle stops until the cause is found.
What does Whirlpool dishwasher code FAE4 mean?
Models like the WDT730PAHZ, a Whirlpool built-in dishwasher, may display FAE4 or F10E4 for one diverter valve error. The diverter sends water to the right spray arms as the cycle moves along; if the control cannot confirm where it sits, the dishwasher stops and shows the code. Owners may see unevenly washed dishes, hear a noise as a cycle starts, or find that the cycle will not continue.
FAE4 at a glance
- Code
- FAE4
- Appliance
- Whirlpool dishwasher
- Applies to
- Whirlpool built-in dishwashers like the WDT730PAHZ
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- The diverter valve itself, its motor or its connector
What you may notice with FAE4
- FAE4 or F10E4 appears on the display
- Dishes come out of the wash unevenly cleaned
- A noise sounds at the start of the cycle
- The cycle will not continue past the start
How the dishwasher detects FAE4
The diverter is a movable valve inside the wash system. It switches the flow of wash water between spray arms as the cycle moves from one stage to the next. To do that, the control commands it into position and expects confirmation, a position feedback signal, that it got there.
FAE4, shown as F10E4 on some displays, appears when the control cannot confirm the diverter's position. The valve could be stuck, its motor or connector might be failing, the wiring to the control might be loose, the control's output might be weak, or the position feedback may fail on its own while the valve works. The result is a stopped cycle, noise at the start, or dishes washed unevenly. A single passing error can clear with a power cycle, but a return means the diverter needs to be examined directly, because it sits inside the wash system.
Likely causes of FAE4
- The diverter valve itself, its motor or its connector
- Wiring running from the diverter to the control
- The control board's output for the diverter
- A passing error that a power cycle clears
Can you keep using the dishwasher with FAE4?
Try one power reset and one cycle. If the code stays away and the dishes come out evenly washed, you can keep using the dishwasher. If FAE4 or F10E4 returns, stop using it, since the control cannot confirm where the diverter sits and the wash may not reach every rack. Leave the dishwasher unplugged until we have examined the diverter.
What you can safely check
- Stop the cycle, then unplug the dishwasher for 30 seconds and plug it back in, or switch the breaker off for the same time if it is hard-wired.
- Push the door shut and begin a cycle.
- Should FAE4 or F10E4 show up again, stop and call us.
What our technician does for FAE4
- Inspect the diverter inside the wash system directly.
- Test the diverter motor or connection and the wiring to the control.
- Check the position feedback, which can fail separately from the valve.
How to keep FAE4 from coming back
- Do not keep resetting the dishwasher after the code returns; note when it appears instead.
- Keep large items from blocking the spray arms so you can tell uneven washing from a valve problem.
Technical reference
- Code
- FAE4
- Appliance
- Whirlpool dishwasher
- Control family
- Whirlpool built-in dishwashers like the WDT730PAHZ
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show FAE4
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool dishwasher error codes
FAE4 questions
What job does the diverter valve perform?
It steers wash water toward the correct spray arm as the cycle moves through its stages. When it sticks or cannot report where it sits, the control halts the cycle and displays the code.
Why do two codes, FAE4 and F10E4, exist for one problem?
Depending on the display, the same diverter valve error is written either way. Our checks and the repair path match for both forms.
How does FAE4 differ from a diverter leak?
FAE4 concerns the valve position and its circuit, while a leak code concerns water escaping. Both involve the diverter, so we inspect for leaks and test the circuit together.
Is FAE4 related to the diverter leak code?
They are neighbors. FAE4 reports a diverter valve error, and the leak code reports water escaping near the diverter. Because both involve the diverter, we check for leaks and test the circuit during the same visit.
Will a power reset fix FAE4?
Sometimes. A passing error can clear when power is cut for 30 seconds. If the code returns, the diverter, its wiring or the control output has a lasting problem, and more resets only delay testing.
Need help with FAE4?
We trace the cause in your home first and write the price down before any part is swapped.
