(813) 565-3059 Book a Repair
What we repair · Tampa Bay

Whirlpool Washer Repair in Tampa Bay

Whirlpool top-load and front-load washers can leak, stop mid-cycle, shake or fail to drain. We find out which part is responsible and repair it for a price you approve in writing.

14 models146 error codesWritten price before work30-day workmanship warranty
Whirlpool washer repair in Tampa Bay

Washers fail in familiar ways: water will not leave, the cycle never finishes, or the drum bangs across the floor. Humidity makes things worse in Florida because a washer that dries slowly will grow odors, and a second home that sits closed for months can have dry seals and stale water in the pump.

Whirlpool builds top-load washers with an agitator or an impeller, and front-load washers with a door boot and a larger drum. They share a drain and fill system but differ in drive, suspension and seals.

Common Whirlpool washer problems we fix

01

Water stays in the drum

A blocked drain pump, a kinked drain hose or a lid or door switch that does not register stops the drain.

02

Stops mid-cycle with flashing lights

The control has detected an unbalanced load, a water problem or a sensor reading it cannot accept.

03

Violent shaking or walking

The load is off center, the feet are unlevel, or the suspension on a top-load is worn.

04

Leak under the washer

A loose hose, a cracked pump housing or a door boot tear is letting water out.

05

Clothes come out wet or still soapy

Spin is weak because of a worn belt, a coupler or a drain restriction.

06

Musty smell

Detergent residue and standing moisture in the door boot or drum are growing odors.

Why will my washer not drain or spin?

Switch the washer off and unplug it before you do anything. Check that the drain hose is not kinked behind the machine and sits at the right height. Then look for a lid switch on a top-load or door lock on a front-load that may not be closing. A coin, sock or hair clip lodged in the drain pump filter is another cause, reachable from the front panel on many front-loaders after the water drains into a pan.

If the pump hums but does not move water, or the drum spins slowly, a belt, coupler or motor part needs testing.

What causes shaking and banging?

A load of one heavy item, such as a comforter or a pair of jeans, throws the drum out of balance. Redistribute the load first. Make sure all four feet touch the floor and the washer does not rock. If it still pounds, suspension rods, snubber pads or a drum bearing may be worn.

Why does the washer smell and leak?

Residue between the door boot and drum feeds odor, so wipe the boot and leave the door ajar after use. Leaks point to a hose, a pump housing, the boot or the tub seal. Turn off the water supply valves if you see a puddle.

How should I care for a washer in a humid home?

Use the amount of detergent the guide gives, especially with high-efficiency models, since extra soap leaves residue that feeds odor. Wipe the door boot and detergent drawer, run a tub-clean cycle on the schedule in your guide, and leave the lid or door ajar between loads. If the home will sit empty for weeks, turn off the water supply valves and unplug the washer. Standing hoses under pressure are a common source of flood damage.

What we check on a visit

  • Drain pump, hoses and inlet valves
  • Lid or door switch and lock
  • Belt, coupler, motor and suspension
  • Door boot, tub seal and bearings
  • Control board and water level sensor

You get the price in writing before work begins, and the labor is covered by a 30-day workmanship warranty.

Error codes

Whirlpool washer error codes

Look the code up before you switch anything off or try a repair. Type it as the display shows it.

1h, 2h, 3h....up to 12hDelay Wash Is SetWhirlpool washerA09Not Enough Water Reaching the MachineWhirlpool washerA10The Water Is Not DrainingWhirlpool washerAdd Garment Light OnYou May Open the LidWhirlpool washerCheck Vent LightClear Airflow Before DryingWhirlpool washerCLRun the Clean Washer CycleWhirlpool washerClean FilterWhirlpool Washer Clean Filter Symbol: Waste Water Is Not Pumping OutWhirlpool washerCycle Complete Light OnThe Wash Is DoneWhirlpool washerDENStore Demo Mode Is OnWhirlpool washerdETDetergent Cartridge Not SeenWhirlpool washerDetergent Level IndicatorYellow Low, Red EmptyWhirlpool washerDetergent Level Indicator LightWhat Yellow and Red MeanWhirlpool washerDetergent LowWhirlpool Washer Detergent Low Message: Refill the HE Liquid DispenserWhirlpool washerdLOWhy the Lid Will Not LockWhirlpool washerDone Light OnWhat It MeansWhirlpool washerDoor OpenWhirlpool Washer Door Open Symbol: Door Will Not LockWhirlpool washerdrnDraining Takes Too LongWhirlpool washerdULid Will Not UnlockWhirlpool washerE1Washer Did Not Fill in TimeWhirlpool washerE2Washer Drain Alarm at 8 MinutesWhirlpool washerE3Washer Load Out of BalanceWhirlpool washerE4Lid Opened During SpinWhirlpool washerELLatch Blocked by Packing or SoapWhirlpool washerErrWhirlpool Front-Load Washer Err Message: Request Not AcceptedWhirlpool washerF 01Power Reset StepsWhirlpool washerF 22Unplug, Wait, RetryWhirlpool washerF 23Reset and RetryWhirlpool washerF 70Cut Power, Then CallWhirlpool washerF 71Reset, Then Get It CheckedWhirlpool washerF0E0Reset the Control FirstWhirlpool washerF0E1Clean Washer Cycle Found a Load in the DrumWhirlpool washerF0E2Excess Suds DetectedWhirlpool washerF0E3Overload, Too Hot or Reset by ModelWhirlpool washerF0E4Water Hotter Than ExpectedWhirlpool washerF0E5Off-Balance Load and Slow SpinWhirlpool washerF0E6Measurement Sensor CircuitWhirlpool washerF0E7Clean Washer Cycle Stopped by a LoadWhirlpool washerF0E8Too Much Water Left in the TubWhirlpool washerF0E9Unbalanced Load at Spin StartWhirlpool washerF0E9 WasherWhirlpool F0E9 Washer Alert: Uneven Basket at Spin StartWhirlpool washerF1 E1Five-Minute Power ResetWhirlpool washerF1 E2Unplug, Wait and Try AgainWhirlpool washerF1E1Control Stop, Reset Time Depends on ModelWhirlpool washerF1E2A Control Stop a Reset May ClearWhirlpool washerF1E3Control Communication MessageWhirlpool washerF1E6Supply Voltage Out of Range or a SurgeWhirlpool washerF1E7Speed Sensor CircuitWhirlpool washerF2 E1Unplug the Washer, Then RetryWhirlpool washerF2 E2Stopped Cycle Waits on a Power ResetWhirlpool washerF20Not Enough Water at FillWhirlpool washerF20 or F60Red Symbol, Unplug and Shut Off the WaterWhirlpool washerF21Washer Cannot Drain, Check the HoseWhirlpool washerF22Door Lock Will Not CloseWhirlpool washerF24Too Much Laundry or Too Much Inlet WaterWhirlpool washerF2E1Stuck Key Reading, Cut Power and Try AgainWhirlpool washerF2E2Communication Message and a Five-Minute ResetWhirlpool washerF2E3Control Unit, Interface or Wiring After a ResetWhirlpool washerF2E4User Interface and Wiring on a CabrioWhirlpool washerF2E5Panel Circuit Alert Mid-WashWhirlpool washerF3 E3Unplug the Washer for Five MinutesWhirlpool washerF3 E5Power Reset Is the Only Owner StepWhirlpool washerF3 E6A Control Stop, Reset the Power FirstWhirlpool washerF3E1Water Level, Pressure and Steam Sensor ReadingsWhirlpool washerF3E2Swapped Hoses, Valves or SensorsWhirlpool washerF3E3Air Inlet or Inlet Temperature Problem ExplainedWhirlpool washerF3E4Load & Go Dispenser Sensor or Tower Motor SensorWhirlpool washerF3E5Mini Dispenser Notice, Dose by HandWhirlpool washerF3E6Rotor Sensor ProblemWhirlpool washerF3E7Reversed Hoses or Temperature SensorWhirlpool washerF3E8General Temperature Sensor AlertWhirlpool washerF4 E1Duet and WFW Reset-Only AlertWhirlpool washerF4 E4Control Message With a Power ResetWhirlpool washerF4E1Steam Heater CircuitWhirlpool washerF4E2Dryer Heater, Water Heating or Main Heater AlertWhirlpool washerF4E3Whirlpool Washer F4E3 Explained: Water Heating Path on Laundry TowersWhirlpool washerF4E4Main Heater Circuit in the WasherWhirlpool washerF4E5Drying Fan Circuit AlertWhirlpool washerF4E6Drying Heater Circuit AlertWhirlpool washerF5E1Why the Door Switch Reads Open Mid-CycleWhirlpool washerF5E2Door or Lid Will Not Lock or LatchWhirlpool washerF5E3Door Will Not Unlock, Latch or Switch ProblemWhirlpool washerF5E4A Reminder to Open the Door After Three CyclesWhirlpool washerF6 E1Duet and WFW Reset-Only MessageWhirlpool washerF6E1Control Communication and Reset-Only MessagesWhirlpool washerF6E2Reboot, Communication and Reset-Only ReadingsWhirlpool washerF6E3Control Boards Not Communicating, or a RebootWhirlpool washerF6E4Boards Not CommunicatingWhirlpool washerF6E5A Control Communication AlertWhirlpool washerF7 E3A Message Read by TestingWhirlpool washerF7 E6Reset the Power, Then Test the WasherWhirlpool washerF7 E8What to Try Before Booking ServiceWhirlpool washerF7 EAAn Unnamed Alert, Reset FirstWhirlpool washerF7 ECOverloaded Drum, Loosen the LoadWhirlpool washerF7E0Older Cabrio Reset MessageWhirlpool washerF7E1Motor Speed Error, Check the Shipping BoltsWhirlpool washerF7E2Control Unit Alerts on Four Washer PlatformsWhirlpool washerF7E3Wash Basket Alert, Reset FirstWhirlpool washerF7E4Wash Basket on a Tower, Reset on an Older CabrioWhirlpool washerF7E5Older Cabrio Alert, Found by TestingWhirlpool washerF7E6Motor Circuit on Towers, Reset Message ElsewhereWhirlpool washerF7E7Motor Sensor on Towers, Control Unit on Top-LoadsWhirlpool washerF7E8Motor Sensor Reading, Reset FirstWhirlpool washerF7E9Motor Sensor on Towers, Main Router on Top-LoadsWhirlpool washerF7EAMotor Sensor on One Tower, Reset on AnotherWhirlpool washerF8E1Whirlpool Washer Code F8E1 and Lo FL: Water Not Detected on FillWhirlpool washerF8E2Clogged Dispenser or Drawer Not ClosedWhirlpool washerF8E3Overflow Alert, Often Linked to SudsWhirlpool washerF8E4Alert from the Flow MeterWhirlpool washerF8E5Hot and Cold Hoses SwappedWhirlpool washerF8E6Water Detected, or No Hot Water on a Top-LoadWhirlpool washerF8E7Steam Valve Needs a CheckWhirlpool washerF9E1Water Is Draining Too Slowly or Not at AllWhirlpool washerF9E2Drain Pump BlockedWhirlpool washerFAE1Shipping Bolts Still InstalledWhirlpool washerFC E0Reset the Control FirstWhirlpool washerFdFactory Default ConfirmationWhirlpool washerFdL or F29The Door Will Not UnlockWhirlpool washerFHWater Not Reaching the TubWhirlpool washerFill or Sensing Light OnNormal Load CheckWhirlpool washerFod or F18Too Much Foam Stopped the CycleWhirlpool washerHCHot and Cold Hoses SwappedWhirlpool washerIntCycle Paused or CanceledWhirlpool washerLdWater Is Slow to Leave the TubWhirlpool washerLdLLid Fails to LockWhirlpool washerLdULid Is Unable to UnlockWhirlpool washerLFThe Tub Is Too Slow to FillWhirlpool washerLidLid Opened During the CycleWhirlpool washerLid Light FlashingClose the Lid or WaitWhirlpool washerLid Lock FlashingLock Fails to EngageWhirlpool washerLo FLNot Detecting Enough Incoming WaterWhirlpool washerLoCWhirlpool Front-Load Washer LoC or LC: Control Lock Is Switched OnWhirlpool washerMultiple Lights FlashingUnbalanced LoadWhirlpool washerNo Water DetectedWhat to CheckWhirlpool washerOFb or ofbLoad Out of BalanceWhirlpool washeroLThe Tub Is OverloadedWhirlpool washerPFPower Failure During the CycleWhirlpool washerRinse Light OnSpray Rinse in ProgressWhirlpool washerrLItems Found During Clean WasherWhirlpool washerSd or 5dSuds Reduction Is RunningWhirlpool washerSense and Wash FlashingUnbalanced SpinWhirlpool washerSpin Light FlashingBasket Off BalanceWhirlpool washerSudToo Many Suds in the TubWhirlpool washeruLUnbalanced Load Needs RearrangingWhirlpool washerWash Light On or FlashingWater Level StuckWhirlpool washerWater Tap is ClosedWhirlpool Washer Water Tap is Closed Symbol: Water Is Not ArrivingWhirlpool washerWhat does the "SUD" or "SD" meanWhirlpool Washer: What does the "SUD" or "SD" mean on the DisplayWhirlpool washer
FAQ

Washer questions

Should I leave the washer door open?

Yes, on a front-load, leaving the door ajar lets the drum and boot dry, which helps with odor.

How often should I replace washer hoses?

Check them for bulges and cracks each year and replace older rubber hoses before they fail. Reinforced hoses are an option.

Is it worth fixing an older washer?

It depends on the part and the age of the machine. We provide a written price so you can compare.

Why does my washer stop with the load still wet?

Unbalanced loads and slow drains are common. Redistribute clothes and run a drain and spin cycle.

Call Book a Repair
Call (813) 565-3059 Book a Repair