Whirlpool Top-Load Washer F0E8: Too Much Water Left in the Tub
F0E8 on a Whirlpool top-load HE washer means too much residual water was detected in the tub. Run a Drain and Spin cycle first, and have it checked if the code stays.
What does Whirlpool washer code F0E8 mean?
On Whirlpool top-load HE washers of the Cabrio and WTW family, such as the WTW5105HW and WTW8500DC, F0E8 means the washer detected too much residual water in the tub. It could not clear the water the way the cycle expects, so it stops and shows the code. You may find a wet load and water standing in the basket. The suggested first step is a Drain and Spin cycle, with a service call if the code remains afterward.
F0E8 at a glance
- Code
- F0E8
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool top-load HE washers, Cabrio and WTW family
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Water left behind by an interrupted or oversudsed cycle
What you may notice with F0E8
- F0E8 appears and the cycle stops
- Water is still standing in the basket
- The load comes out soaking wet
- The washer will not move on to the spin
How the washer detects F0E8
After the drain step, the washer expects the tub to be nearly empty before it moves on to the spin. The control reads the water level through its sensing, and if too much water remains it holds the cycle and shows F0E8.
The leftover water can come from several places. A cycle that was interrupted or heavily oversudsed may leave water behind. A kinked or clogged drain hose, or a house drain that is blocked, keeps the pump from emptying the tub. Small items such as socks can catch near the pump. When the drain path is clear but the water still stays, the drain pump or the level sensing itself may be the cause, which is why a technician checks the path first and then those two parts.
Likely causes of F0E8
- Water left behind by an interrupted or oversudsed cycle
- Kinked or clogged drain hose, or a blocked house drain
- Small items caught near the pump
- Drain pump or water level sensing
Can you keep using the washer with F0E8?
Wait until the water is gone. A tub full of water is heavy and can overflow when you open the lid or reach in. Try a Drain and Spin cycle, and check the hose and basket. If the washer drains and runs normally afterward, you can keep using it. If F0E8 comes back or the water stays, stop and leave the washer unplugged until it has been checked.
What you can safely check
- Stop the washer and unplug it or switch off its breaker before reaching toward the hose or the basket.
- Plug in and run a Drain and Spin cycle.
- Check the drain hose behind the washer for a kink.
- Look for a sock or small item in the basket that could block drainage.
- If the water stays or F0E8 returns, stop and call us.
What our technician does for F0E8
- Test the drain pump
- Test the water level sensing
- Tell a washer problem from a house drain problem
How to keep F0E8 from coming back
- Use only HE detergent in a measured dose to avoid oversudsing
- Check the drain hose for kinks after moving the washer
- Check pockets for socks and small items before washing
Technical reference
- Code
- F0E8
- Appliance
- Whirlpool washer
- Control family
- Whirlpool top-load HE washers, Cabrio and WTW family
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show F0E8
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool washer error codes
F0E8 questions
Why is there water left in my Cabrio?
The washer detected too much residual water in the tub. A Drain and Spin cycle is the first step, because it may clear a one-time slow drain without any repair.
Should I bail out the water?
Unplug the washer first. Small amounts can be removed with a cup and towels. If a lot of water remains, wait for us rather than tipping or moving the machine.
Is a pump replacement worth it on an older washer?
It can be a moderate repair. We give a written price and say plainly if the age of the machine means it is better not to fix it.
Will F0E8 clear by itself?
Sometimes a Drain and Spin cycle clears a one-time slow drain, and the code goes. If the water stays or the code returns, the drain path or the pump is still the problem and the washer needs checking.
Does F0E8 mean the house drain is blocked?
It can, but it does not prove it. If other drains in the home are slow too, tell us. We check the washer's pump and hose and can say whether the problem sits in the house line.
Need help with F0E8?
We trace the cause in your home first and write the price down before any part is swapped.
