Whirlpool Washer Code A10: The Water Is Not Draining
A10 on a Whirlpool washer means the water did not drain; the drain hose is the first place to look for a kink, frozen water, a clog or a hose hooked up too high.
What does Whirlpool washer code A10 mean?
Whirlpool washers report A10 as a drain problem, in guidance that names no series. The washer failed to empty its water, so A10 appears and water may be left in the tub. All the questions concern the drain hose: is it kinked, frozen, clogged, or hooked up above 55 inches (1.4 m) from the floor? As the guidance asks, unplug the washer or cut its power first, then check the hose.
A10 at a glance
- Code
- A10
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool washers, product-assistance drain code, no series named
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A kinked drain hose
What you may notice with A10
- A10 is showing on the display
- Water remains in the tub after the cycle stops
- The drain hose looks bent or sits unusually high
How the washer detects A10
After the wash and rinse stages, a washer pumps used water out through the drain hose into a standpipe or sink. The control expects the level in the tub to fall within a set time once the pump runs.
A10 appears when it does not. The pump may be pushing against a hose that is kinked or crushed, or one frozen or clogged at the standpipe. The hose may also be hooked up too high, above 55 inches (1.4 m) from the floor, which makes lifting the water hard for the pump. In every case the water stays in the tub, and the control stops the cycle rather than carry on with a full drum. If the hose is clear and at the right height, the drain pump, its filter and its circuit come next.
Likely causes of A10
- A kinked drain hose
- A frozen drain hose
- A clogged drain hose
- A drain hose hooked up higher than 55 inches above the floor
Can you keep using the washer with A10?
Do not keep restarting the washer on A10 with water in the tub. Switch off and unplug it, then check the hose as the guidance describes. Wet clothes can wait in the drum a short while, but they will start to smell, so remove them once the water is dealt with. If the hose is clear and A10 returns, have the drain checked.
What you can safely check
- Disconnect power or unplug the washer, and keep towels near because water may be left.
- Follow the drain hose and look for kinks or a crushed section.
- See whether the hose has frozen.
- Make sure nothing clogs it where it meets the standpipe.
- Confirm it sits no higher than 55 inches above the floor, restore power, and if A10 returns, contact us.
What our technician does for A10
- Test the drain pump and its filter
- Test the control that runs the pump
How to keep A10 from coming back
- Keep the drain hose straight, supported and below 55 inches above the floor.
- Avoid pushing the washer tight against the wall, which can crush the hose behind it.
Technical reference
- Code
- A10
- Appliance
- Whirlpool washer
- Control family
- Whirlpool washers, product-assistance drain code, no series named
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
A10 questions
Why is water still in the tub with A10?
The code says draining did not happen. Begin with the hose, because a kink, ice, a clog or too high a hookup can each stop the flow.
Does the 55-inch figure matter?
Yes. A drain hose hooked up above 55 inches (1.4 m) from the floor is listed as a cause, so see how yours is arranged before blaming the washer.
Must I unplug first?
Yes, as the guidance asks, before checking the hose. Water may remain in the tub or the hose, so keep towels handy.
Can a clogged standpipe cause A10?
Yes, since the guidance lists a clog where the hose meets the standpipe among the checks. A standpipe or household drain that is backed up can look just like a washer problem.
Is A10 the same as the red Clean Filter symbol?
They are related, since both involve water not leaving the tub. A10 is a drain code that starts with the hose, while the symbol also points you toward the drain pump filter. Their checks overlap.
Need help with A10?
We trace the cause in your home first and write the price down before any part is swapped.