Whirlpool Top-Load Washer Code Ld: Water Is Slow to Leave the Tub
Ld is the long drain alert on an older Whirlpool top-load HE washer. The water is taking too long to leave, sometimes because the drain hose sits too deep in the standpipe.
What does Whirlpool washer code Ld mean?
Ld on an older Whirlpool top-load HE washer from the Cabrio and WTW family is the long drain alert. The display shows it when the washer takes too long to get rid of its water. The drain hose may reach more than 4.5 inches into the standpipe, which lets water siphon back, or the hose may be kinked or clogged. You may find water still in the tub, a cycle that stalls before the spin, or damp clothes at the end.
Ld at a glance
- Code
- Ld
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Cabrio and WTW top-load HE washers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Drain hose pushed too far into the standpipe
What you may notice with Ld
- Ld on the display and water left in the tub
- A cycle that stalls before the spin
- Damp clothes left in the tub at the end
- A hose set deep in the standpipe or bent behind the washer
How the washer detects Ld
During drain steps the washer runs its pump and expects the water level in the tub to fall within a set time. A sensor reports the level to the control. If the water has not dropped by the expected amount when the time is up, the control calls it a long drain and shows Ld.
Anything that slows the outflow can trigger this. A kinked or partly clogged hose restricts the flow. A hose pushed deeper than 4.5 inches into the standpipe, or a standpipe that sits too high, can let water siphon back into the tub, so the level never falls as the control expects. Only after the hose and standpipe are right does the pump and its circuit become the likely reason.
Likely causes of Ld
- Drain hose pushed too far into the standpipe
- Drain hose kinked or partly clogged
- Standpipe height or fit that lets the washer siphon
- Drain pump or its circuit, once the path is clear
Can you keep using the washer with Ld?
Try one corrected cycle after you pull the hose back and straighten it. If the tub empties and Ld stays away, you can keep using the washer. If water stays behind or Ld returns, stop running loads, because standing water can lead to odors and an overflow. Leave the washer unplugged until someone has tested the drain.
What you can safely check
- Stop the cycle and make sure the washer has finished pumping, or unplug it.
- Pull the drain hose back so it enters the standpipe no more than 4.5 inches, keeping the hose form as shipped.
- Straighten any bend and clear the hose and standpipe of blockage.
- Run a Drain & Spin cycle and see whether Ld returns.
- If it does, stop using the washer and call us.
What our technician does for Ld
- Watch the drain flow with the hose set correctly
- Test the drain pump
- Check the standpipe height and fit
- Test the pump circuit if the path is clear
How to keep Ld from coming back
- Seat the drain hose loosely in the standpipe, no deeper than 4.5 inches, keeping the hose form as shipped
- Avoid taping or sealing the hose to the standpipe
- Keep the hose free of kinks when you slide the washer back after cleaning
- Clear lint or debris from the standpipe if drains turn slow
Technical reference
- Code
- Ld
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Cabrio and WTW top-load HE washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
Ld questions
Why does Ld depend on the standpipe?
If the hose is pushed too far in, or the standpipe sits too high, water can siphon, filling and draining at once. The washer then reads the drain as too slow and shows Ld.
Can I tape the drain hose in place?
Please do not. Keep the hose form as shipped, since taping it to the pipe can seal the air gap that prevents siphoning. Seat it loosely at the right depth.
Is it safe to keep running loads with Ld?
Try one corrected cycle. If water stays in the tub or the code returns, stop and have the drain checked, since standing water can bring odors and an overflow into the laundry room.
What does Ld stand for?
Ld is short for Long Drain on these Cabrio and WTW washers. It says the water took too long to leave the tub. The drain hose, the standpipe and the pump are checked in that order.
Will Ld clear by itself?
Not if the hose depth or a blockage is still there. Correcting the hose and clearing the line lets the next cycle drain properly. If Ld repeats with a correct setup, the pump and its circuit need testing.
Need help with Ld?
We trace the cause in your home first and write the price down before any part is swapped.