(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Laundry Center Code E2: Washer Drain Alarm at 8 Minutes

E2 on the washer section of an older Whirlpool stacked laundry center is a draining alarm. The control saw water still draining after 8 minutes and stopped the cycle.

Needs attention soonChecked November 2026

What does Whirlpool washer code E2 mean?

E2 is a draining alarm on the washer section of an older Whirlpool stacked laundry center, one of the models that print error codes. The control sees water still draining after 8 minutes and stops the cycle. You find standing water in the tub, a washer that will not spin and E2 on the display. The first suspects are a kinked or clogged drain hose, a hose raised higher than 100 cm above the floor and a standpipe that cannot take the flow.

E2 at a glance

Code
E2
Appliance
Whirlpool washer
Applies to
Older Whirlpool stacked laundry center, washer section
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Clog or kink in the drain hose

What you may notice with E2

  • E2 appears on the washer display
  • Water stands in the tub after the drain step
  • The washer will not spin once the drain stalls
  • Gurgling or slow water at the standpipe

How the washer detects E2

When the washer reaches a drain step, it starts the pump and expects the tub to empty within a set time. The control allows 8 minutes for this. If water is still draining when that time ends, the control stops the cycle and shows E2.

The pump is only one part of the path. Water has to travel through the drain hose and into the standpipe, and anything that restricts that route slows the drain. A hose with a kink or clog, a hose end raised above 39 1/3 inches (100 cm) from the floor or a standpipe that is backing up all stretch the time past the limit. The control cannot tell which one it is, so it reports the slow drain and lets the checks begin at the hose.

Likely causes of E2

  • Clog or kink in the drain hose
  • Drain hose raised above the 100 cm limit from the floor
  • Drain pump slow or partly blocked
  • Standpipe or house drain backing up

Can you keep using the washer with E2?

Hold off until the water has drained and the cause is found. A tub full of water is heavy and can spill when the lid is opened, and running more loads into a slow drain makes it worse. Check the hose and standpipe. If the tub drains normally afterward, you can keep using the unit. If E2 returns, stop and have the pump and drain path tested.

What you can safely check

  1. Stop the cycle and unplug the unit, then keep towels and a shallow pan ready for leftover water.
  2. Check that the drain hose is not more than 39 1/3 inches (100 cm) above the floor.
  3. Straighten any kink and remove clogs you can see from the hose.
  4. Make sure the wall standpipe is clear.
  5. Plug in and restart. Call us if E2 returns or the tub stays full.

What our technician does for E2

  • Inspect the drain pump and its passage
  • Tell a washer drain problem from a house line problem
  • Test the pump circuit if the hose and standpipe are clear

How to keep E2 from coming back

  • Keep the drain hose below the 100 cm limit and free of kinks
  • Check the hose when you move the laundry center for cleaning
  • Catch lint and small items before they reach the drain, since they can build into a clog

Technical reference

Code
E2
Appliance
Whirlpool washer
Control family
Older Whirlpool stacked laundry center, washer section
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

E2 questions

What triggers E2 on this washer?

The washer is still pumping water out after 8 minutes, so it gives up and stops the cycle. A kinked or blocked hose, or a hose set too high, is the first thing we look at.

Will water spill when I check the hose?

Some may. Unplug the unit, put towels and a shallow pan under the connection before you pull it free, and keep the free end low so the water runs into the pan.

Should I replace this old laundry center?

Not necessarily. A clogged hose costs far less than a new unit. We quote first and tell you plainly if the machine's age says to save your money.

Will E2 clear on its own?

Only if the cause was brief, such as a one-time clog that passed. A kinked or blocked hose will keep slowing the drain, so check the hose and standpipe before you start another cycle.

What should I report about the E2 drain alarm?

Tell us it is a stacked laundry center showing E2, whether water stays in the tub and whether the hose is kinked. Mention if other drains in the home are slow too.

Need help with E2?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair