(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Top-Load Washer drn: Draining Takes Too Long

drn on a Whirlpool top-load HE washer is a long drain alert, the same condition the washer can report as F9 E1. The drain hose installation is the first place to look.

Needs attention soonChecked November 2026

What does Whirlpool washer code drn mean?

drn is shown on Whirlpool top-load HE washers of the Cabrio and WTW style, such as the WTW5000DW, WTW5105HW, WTW7500GC and WTW8500DC. It is a long drain alert, the same condition the washer can report as F9 E1, and it means water is leaving the tub too slowly. The cause may sit in how the drain hose was installed: pushed more than 4.5 inches into the standpipe, a hose end set too low, or a hose that is kinked or clogged.

drn at a glance

Code
drn
Appliance
Whirlpool washer
Applies to
Whirlpool top-load HE washers, Cabrio and WTW style
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Drain hose pushed farther than 4.5 inches into the standpipe

What you may notice with drn

  • The code drn appears on the washer display
  • Water sits in the tub after the drain step
  • The cycle stops before the spin
  • Gurgling at the standpipe as the washer drains

How the washer detects drn

During the drain step, the washer starts its pump and expects the tub to empty within a set time. The control watches how quickly the water level falls, and if it takes too long it stops the cycle and reports drn, or F9 E1 on models that use that wording.

The pump may be working fine while the water still leaves slowly, because the installation controls the flow. A hose pushed too far into the standpipe, a hose end below 36 inches from the floor or a kinked or clogged hose all hold the water back or let it siphon back into the tub. That is why the first checks are about the hose, and only after they pass do the pump and its circuit come under suspicion.

Likely causes of drn

  • Drain hose pushed farther than 4.5 inches into the standpipe
  • Hose end below 36 inches from the floor so the washer siphons
  • Drain hose kinked or clogged
  • Drain opening taped over

Can you keep using the washer with drn?

Wait before running another load. A washer that cannot drain can hold a full tub of water and clothes, and trying again without checking the hose may only repeat the stop. Fix the hose installation, clear any kink or clog and run a drain cycle. If water leaves normally, you can keep using the washer. If drn returns, stop and have the pump and its circuit tested.

What you can safely check

  1. Stop the cycle, unplug the washer or switch off its breaker, and have towels ready for leftover water.
  2. Check how far the hose goes into the standpipe; it should not go more than 4.5 inches (114 mm).
  3. Confirm the hose end is higher than 36 inches from the floor.
  4. Look for kinks and clogs, and remove any tape over the drain opening.
  5. Restart. Call us if drn returns after the installation checks.

What our technician does for drn

  • Run a drain cycle and watch how fast the tub empties
  • Test the drain pump and its circuit
  • Inspect the hose path and standpipe connection

How to keep drn from coming back

  • Keep the drain hose no deeper than 4.5 inches in the standpipe
  • Hold the hose end higher than 36 inches from the floor
  • Check behind the washer for kinks after moving it or cleaning behind it
  • Never tape over the drain opening of the hose

Technical reference

Code
drn
Appliance
Whirlpool washer
Control family
Whirlpool top-load HE washers, Cabrio and WTW style
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show drn

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

drn questions

What is the difference between drn and F9 E1?

They describe the same condition, which is the washer taking too long to drain. Your model shows one or the other, and the drain hose installation is the first thing to check for either.

Why does the hose height matter?

If the hose end is not higher than 36 inches from the floor, the washer can siphon, filling and draining at once. That can make it look as if the water will not leave.

Should I tape the hose to the drain?

No. Do not tape over the drain opening. Use the drain hose form and fasten the hose to the drainpipe or tub in the way the guidance describes.

Will drn clear by itself?

Not if the hose installation is the cause. A kink, a deep hose or a low hose end will keep slowing the drain until you correct it, so check behind the washer before another load.

What facts help you find the cause of drn?

Tell us your model, whether the display shows drn or F9 E1, and how far the hose goes into the standpipe. It also helps to say whether water stands in the tub.

Need help with drn?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair