(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Washer Clean Filter Symbol: Waste Water Is Not Pumping Out

A red Clean Filter symbol on some Whirlpool washers says waste water is not being pumped out; a kinked or blocked hose, a blocked filter or a blocked pump may be behind it.

Needs attention soonChecked November 2026

What does Whirlpool washer code Clean Filter mean?

On some Whirlpool washers, guidance that names no series, a red Clean Filter symbol lights up. Waste water is not leaving the washer. Four reasons are given: a kink in the drain hose, a hose that is blocked or frozen, a clogged filter, or a blocked pump. The tub keeps its water because something restricts the drain path, and the red symbol directs you to the drain pump filter first.

Clean Filter at a glance

Code
Clean Filter
Appliance
Whirlpool washer
Applies to
Whirlpool washers, red Clean Filter symbol, no series named
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A kinked drain hose

What you may notice with Clean Filter

  • A red symbol lights on the control panel
  • Water stays standing in the tub
  • The washer stops before the cycle is finished

How the washer detects Clean Filter

When a wash stage ends, a pump pushes the used water out of the tub and along the drain hose. Between the tub and the pump sits a filter that catches lint, coins and other debris before they can jam the pump. The control checks that the water leaves.

When it does not, the red symbol lights. Four things can hold the water back. The drain hose may be kinked, blocked, or frozen in a cold room. The filter may be clogged with lint and small items. Or the pump itself may be blocked. Each stops the flow in a different place, yet the tub ends up with water still in it, so the control reports one symbol for all of them. The guidance leads you to the filter first because it is the one part meant to be cleaned.

Likely causes of Clean Filter

  • A kinked drain hose
  • A blocked or frozen drain hose
  • A drain pump filter packed with lint or debris
  • A blocked drain pump

Can you keep using the washer with Clean Filter?

Do not keep running the washer while the red symbol is lit and water sits in the tub. Switch off, unplug, and drain with care, using towels. After you clean the filter and straighten the hose, try once more. If the symbol returns, the pump or its circuit needs testing, and the washer should stay off until then.

What you can safely check

  1. Switch the washer off and unplug it, and lay towels down because water will be left in the tub.
  2. Look the drain hose over for kinks.
  3. Make sure the washer stands in a room that does not drop below 41 degrees F.
  4. Clean the drain pump filter the way your owner's manual describes.
  5. Touch Start/Pause once the cause is fixed; if the symbol stays, hold Power for at least three seconds, then contact us.

What our technician does for Clean Filter

  • Test the drain pump and its circuit with the water drained first
  • Check the hose and filter again if the symbol returns

How to keep Clean Filter from coming back

  • Empty pockets before washing, because coins and small items are what reach the pump filter.
  • Clean the drain pump filter as the manual describes, a little at a time, rather than waiting for a full blockage.

Technical reference

Code
Clean Filter
Appliance
Whirlpool washer
Control family
Whirlpool washers, red Clean Filter symbol, no series named
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Clean Filter questions

Why will my washer not drain?

The red symbol says the used water is not being pumped away. A kinked, blocked or frozen hose, a clogged filter and a blocked pump make up the list of reasons, so the filter and the hose are the first checks.

Is opening the drain pump filter safe?

Do it as your owner's manual describes. Expect leftover water, so lay out towels and a shallow pan beforehand. If you are not comfortable with it, we can take care of it.

What is the point of holding Power for three seconds?

The guidance asks for it when the problem continues after Start/Pause. If the symbol still shows after that, the drain system needs testing.

How does this symbol relate to other drain codes?

Any drain message means water did not leave the tub, and the hose is part of every one. This symbol also sends you to the drain pump filter, so the checks overlap heavily.

What should I tell you if the symbol stays?

Say what you already cleaned, whether the hose was straight, and whether water stays in the tub. That helps us decide whether the pump needs testing.

Need help with Clean Filter?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair