(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Front-Load Washer Error FH: Water Not Reaching the Tub

FH on a Whirlpool Duet or WFW front-load washer means no water, or too little, is arriving. The cause sits on the supply side: faucets, hoses, hose screens or the inlet valve.

Needs attention soonChecked November 2026

What does Whirlpool washer code FH mean?

FH on a Whirlpool front-load washer of the Duet and WFW family, current or older, reports a water inlet problem. Little or no water is reaching the tub. The washer waits for the fill, gives up and shows FH. It differs from Lo FL and F8 E1, which describe the sensed fill amount, because FH points at the supply side. Closed faucets, kinked hoses and clogged screens where the hoses meet the washer are the likely culprits. Models such as the WFW5620HW and WFW9150WW show it this way.

FH at a glance

Code
FH
Appliance
Whirlpool washer
Applies to
Whirlpool Duet and WFW front-load washers
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A hot or cold faucet that is only partly open

What you may notice with FH

  • FH on the display and an empty or nearly empty tub
  • A washer that waits and then stops the cycle
  • A faint trickle or no sound of filling
  • Hoses that look flattened or bent behind the cabinet

How the washer detects FH

At the start of the wash, the control opens the inlet valve and waits for the water level sensor to report that the tub is filling. It allows a set period for the level to reach the needed amount. If the fill is absent or far too slow, the control stops waiting and shows FH.

The code watches the supply side. Water has to pass the wall faucets, the two hoses, the small screens at the washer and finally the inlet valve. A closed faucet, a pinched hose or a screen packed with sediment cuts the flow. Lo FL and F8 E1 are different, because they report that the amount of incoming water sensed was wrong. FH says the water simply is not arriving as it should.

Likely causes of FH

  • A hot or cold faucet that is only partly open
  • Inlet hose kinked or crushed behind the washer
  • Screens at the hose connections clogged with sediment
  • Inlet valve or control circuit, once the supply is confirmed

Can you keep using the washer with FH?

You can try one short cycle after opening both faucets fully and straightening the hoses. If FH appears again, stop and do not keep restarting, because the washer may run with too little water. Leave the faucets shut when you are away if you suspect a hose problem. A confirmed strong supply with FH still showing means the valve or control needs testing.

What you can safely check

  1. Press Pause/Cancel twice to end the cycle, then unplug the washer.
  2. Make sure both the hot and cold faucets are open all the way.
  3. Look at each inlet hose for a bend or a flattened spot.
  4. Close the faucets, then look at the screens where the hoses attach for debris, and reconnect them by hand.
  5. Run a short cycle. If FH returns with strong water at the faucets, call us.

What our technician does for FH

  • Measure the water arriving at the hoses
  • Clean or replace clogged inlet screens
  • Test the inlet valve circuit
  • Check the control output that opens the valve

How to keep FH from coming back

  • Open the hot and cold faucets fully after any plumbing work or when moving the washer
  • Keep the washer pulled out far enough that the hoses are never pinched against the wall
  • Clean the hose screens when you replace hoses or after a water main flush
  • Replace aging inlet hoses before they crack, especially where hard or well water leaves deposits

Technical reference

Code
FH
Appliance
Whirlpool washer
Control family
Whirlpool Duet and WFW front-load washers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

FH questions

Is FH the same as Lo FL?

No. FH says water is missing or short on the supply side, while Lo FL and F8 E1 say the sensed amount of incoming water is wrong. We check the supply for both but read them as separate codes.

Why would the hose screens clog?

Sediment, scale and rust flakes from household plumbing collect in the small screens at the hose ends. After plumbing work or a main flush, they can catch more debris than they normally do.

Can weak water pressure set off FH?

Yes. A half-closed shutoff or weak house pressure can make the fill too slow. If other faucets run strong and only the washer struggles, suspect the hoses, screens or inlet valve.

What happens if I ignore FH?

The washer will not complete a proper wash, because it cannot fill the tub. Clothes stay dry or only partly wet. A weak supply can also mean a hose is damaged, so it is better to check the cause than to keep restarting.

What should I tell you about FH?

Say that FH shows, whether both faucets are fully open, and whether other taps in the house run strong. If you checked the hoses and screens, mention what you found. It tells us whether to start at the supply or at the inlet valve.

Need help with FH?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair