Whirlpool Front-Load Washer Message No Water Detected: What to Check
No Water Detected on a Whirlpool Duet or WFW front-load washer means the same as F8 E1 and Lo FL. The washer does not sense the right amount of incoming water, so check faucets and hoses.
What does Whirlpool washer code No Water Detected mean?
The message No Water Detected on a Whirlpool front-load washer from the Duet and WFW family means the same as F8 E1 and Lo FL: the washer does not sense the correct amount of incoming water. The door may be locked, and the control may not answer the keys. Pressing Power begins a drain routine of about 8 to 10 minutes with the pump running continuously, during which no input is accepted. Models such as the WFW90HEFW display it this way.
No Water Detected at a glance
- Code
- No Water Detected
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Duet and WFW front-load washers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Water faucets not fully open
What you may notice with No Water Detected
- No Water Detected on the display
- A door that stays locked and keys that do nothing
- A pump that runs for several minutes
- A tub that is empty or only partly filled
How the washer detects No Water Detected
The control opens the fill valves and watches the water level sensor to see how much water enters the tub over time. It compares what it senses with what it expects. When the amount is not right, it reports No Water Detected, which is the same reading shown as F8 E1 and Lo FL on other displays.
After posting the message, the washer runs a drain routine. The pump works without a pause for about 8 to 10 minutes and the keys are locked out, so the tub is empty before you try again. When the routine ends, the supply is the first thing to check, from the faucets to the hoses to the screens at the washer. If water reaches the washer freely, the fill valve or the level sensing circuit is the next suspect.
Likely causes of No Water Detected
- Water faucets not fully open
- Inlet hoses kinked, off or on the wrong inlets
- Debris in the inlet screens limiting the flow
- Fill valve or water level circuit
Can you keep using the washer with No Water Detected?
Wait the full ten minutes for the drain routine, then open both faucets all the way, straighten the hoses and run a short cycle. If the tub fills and the wash completes, carry on. If the message returns, stop using the washer instead of repeating the cycle, and leave it idle until the fill valve and sensing have been tested.
What you can safely check
- Press Power once, and keep your hands away from the door while the washer works.
- Give the washer a full 10 minutes to finish its drain routine.
- Open both the hot and cold faucets all the way.
- Straighten any bent hose, and confirm hot goes to hot and cold to cold.
- Start a short cycle, and call us if the message returns.
What our technician does for No Water Detected
- Measure the water arriving at the hoses
- Clean the inlet screens
- Test the fill valve
- Check the water level sensing circuit
How to keep No Water Detected from coming back
- Keep both faucets fully open and the hoses free of kinks
- Check that hot is on the hot inlet and cold on the cold inlet after any move
- Clean the inlet screens if your water carries sediment or scale
- Do not crush the hoses when you push the washer back against the wall
Technical reference
- Code
- No Water Detected
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Duet and WFW front-load washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
No Water Detected questions
Does the message mean my house has no water?
Not necessarily. It means the washer did not see the expected amount arrive in the time allowed. Closed or partly closed faucets, a kinked hose or clogged screens are the likely reasons.
Why can't I press any buttons?
The washer is running its drain routine, which takes about 8 to 10 minutes. The pump runs the whole time and the keys are ignored. Wait the full ten minutes before trying again.
How is this different from FH?
FH says the supply itself is absent or short. This message says the amount sensed was wrong. We check the same faucets, hoses and screens for both, but they come from different readings.
Is No Water Detected the same as Lo FL?
Yes. On these front-load washers, No Water Detected, F8 E1 and Lo FL describe the same condition, and the display of your model decides which one you see. The checks are identical for all three.
What should I tell you about No Water Detected?
Give us the model number and say whether the faucets and hoses were checked. Mention whether the washer ran its 8 to 10 minute drain routine and whether any water entered the tub. That shows where to start.
Need help with No Water Detected?
We trace the cause in your home first and write the price down before any part is swapped.