Whirlpool Front-Load Washer Lo FL: Not Detecting Enough Incoming Water
Lo FL, like F8 E1, means a Whirlpool Duet or WFW front-load washer is not detecting the right amount of incoming water. Wait out the drain routine first, then check faucets and hoses.
What does Whirlpool washer code Lo FL mean?
Lo FL, like F8 E1, tells you a Whirlpool front-load washer from the Duet and WFW family is not detecting the correct amount of incoming water. The door can be locked and the control can seem dead. Pressing Power begins a drain routine in which the pump runs nonstop for about 8 to 10 minutes and no input is accepted, so wait ten minutes before trying anything else. The WFW5620HW and WFW9150WW are two examples of models that display it.
Lo FL at a glance
- Code
- Lo FL
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Duet and WFW front-load washers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Either faucet closed or only partly opened
What you may notice with Lo FL
- Lo FL on the display with the door locked
- Keys that do not respond for several minutes
- A pump running without a pause
- An empty or only partly filled tub
How the washer detects Lo FL
The washer opens its inlet valves and then measures how much water has arrived by watching the level sensor. It expects the tub to gain water at a certain pace. When the amount it senses is wrong, either too little or not matching the fill command, the control stops and posts Lo FL. F8 E1 is the same message on other displays.
Before it accepts new commands, the washer runs a drain routine. The pump runs continuously for about 8 to 10 minutes, and the keys are ignored in that time. That can look like a dead control, but it is the washer clearing the tub. After the routine ends, the supply is the first suspect: faucets, hoses and the screens where the hoses attach. If those are fine, the inlet valve or the level sensing is next.
Likely causes of Lo FL
- Either faucet closed or only partly opened
- Inlet hose kinked or connected to the wrong inlet
- Screens at the inlet clogged
- Inlet valve or water level sensing circuit
Can you keep using the washer with Lo FL?
Wait the full ten minutes before you try anything, since the washer ignores the keys during its drain routine. Then open both faucets fully, straighten the hoses and run one short cycle. If it fills and washes normally, you can keep using it. If Lo FL returns, stop and leave the washer idle until the inlet valve and sensing are tested.
What you can safely check
- Stop the cycle by pressing Power once, and keep your hands away from the door and drum.
- Wait a full 10 minutes while the washer runs its drain routine.
- Confirm both faucets are open all the way and both inlet hoses are connected.
- Check that neither hose is kinked and that the hot (red) hose is on the hot inlet.
- Try a short cycle, and call us if Lo FL returns.
What our technician does for Lo FL
- Measure the incoming flow at the hoses
- Clean or replace the inlet screens
- Test the inlet valve
- Check the water level sensing circuit
How to keep Lo FL from coming back
- Keep both faucets fully open and the hoses free of bends
- Match the red hose to the hot inlet and the blue hose to the cold inlet after any move
- Clean the inlet screens if your water carries sediment
- Replace stiff or kinked hoses before they restrict the flow
Technical reference
- Code
- Lo FL
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Duet and WFW front-load washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
Lo FL questions
Why is my washer unresponsive with Lo FL on?
The control is running a drain routine and ignores the keys for 8 to 10 minutes. The door may stay locked. Waiting the full ten minutes is the right first step.
Is Lo FL the same as FH?
They are related but not identical. Lo FL says the incoming water amount is wrong, while FH says the water supply is absent or short. The faucets, hoses and screens get checked for both.
Do I need to reverse any hoses?
Only if they are on the wrong inlets. The hot hose, red, goes to the hot inlet and the cold hose, blue, to the cold inlet. Otherwise leave the connections alone.
Is Lo FL the same as F8 E1 and No Water Detected?
They describe the same condition on these front-load washers. Which one you see depends on the model and the display. All three mean the washer does not sense the correct amount of incoming water, and the checks are the same.
What should I tell you about Lo FL?
Tell us the model number, whether the faucets and hoses were checked and whether the washer ran its 8 to 10 minute drain routine. If it filled at all, say how far. That helps us find where the water stops.
Need help with Lo FL?
We trace the cause in your home first and write the price down before any part is swapped.