(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Laundry Tower Washer F1E3: Control Communication Message

F1E3 on the washer section of a Whirlpool laundry tower or stacked laundry center points to control communication. A 30-second power reset is the one owner step.

Needs attention soonChecked November 2026

What does Whirlpool washer code F1E3 mean?

F1E3 appears on the washer section of a Whirlpool laundry tower or stacked laundry center and points to control communication. In plain words, parts of the control are not talking to each other the way they should. The display does not say whether the cause is the board, a wire between boards or a one-time glitch. You see F1E3, and the washer stops. The one owner step is to cycle power, with service if the code returns.

F1E3 at a glance

Code
F1E3
Appliance
Whirlpool washer
Applies to
Whirlpool laundry tower or stacked laundry center, washer section
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
One-time communication glitch that clears with a reset

What you may notice with F1E3

  • F1E3 appears and the washer stops
  • The code names communication, not a single part
  • The code returns after a 30-second reset
  • The dryer section above may still run

How the washer detects F1E3

The electronics of the washer section are made of more than one control part, and those parts constantly exchange signals about what each step of the cycle needs. When the exchange breaks down, the washer cannot be sure what is happening and stops, showing F1E3.

The display does not tell us where the exchange failed. It may have been a one-time glitch that a 30-second power reset clears. It may also be a loose or damaged connection between control boards, or a board that has stopped answering. Because the reset only separates a one-time event from a lasting one, a technician checks the connections and boards on site when the code returns, and does not guess at a part.

Likely causes of F1E3

  • One-time communication glitch that clears with a reset
  • Loose or damaged connection between control boards
  • Control board that has stopped answering

Can you keep using the washer with F1E3?

After one reset, yes, if the washer runs a cycle normally. If F1E3 returns, stop and do not keep resetting, because a failing link between boards will not repair itself. Check the plug and cord for damage. If you notice heat, a burning smell or sparking near the outlet, keep the unit unplugged until it has been inspected.

What you can safely check

  1. Stop the washer and unplug it; do not open any panel.
  2. Wait 30 seconds.
  3. Plug it in and make sure the plug is fully seated.
  4. Close the lid or door and start a short cycle.
  5. If F1E3 shows once more, stop and call us.

What our technician does for F1E3

  • Check the connections between the boards
  • Test the control boards on site
  • Find which link in the control chain dropped out

How to keep F1E3 from coming back

  • Seat the plug fully and keep the cord undamaged
  • Use a surge protector so storms do not upset the boards
  • Keep the area behind the unit dry so connections stay clean

Technical reference

Code
F1E3
Appliance
Whirlpool washer
Control family
Whirlpool laundry tower or stacked laundry center, washer section
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F1E3 questions

What does control communication mean?

It means two parts of the washer's electronics are not exchanging signals correctly. The code does not say which, so we test the connections and boards in person.

Will a 30-second reset be enough?

It can be, if the problem was a one-time glitch. If F1E3 returns after it, resetting again will not help and a visit is the next step.

Is the dryer on top affected?

It may be on the same unit, but this code belongs to the washer section. Tell us when you call if the dryer also acts strangely.

Is F1E3 related to F1E2?

Both are control-level codes on a laundry tower, but F1E2 lists the main control and F1E3 points to communication between control parts. The 30-second reset is the same first step for each.

Will F1E3 clear by itself?

Only if it was a one-time glitch. A reset of 30 seconds gives the boards a fresh start. If the code comes back, a connection or a board is still involved and needs testing.

Need help with F1E3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair