(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Stacked Laundry Center Washer F 22: Unplug, Wait, Retry

F 22 on the washer half of an older Whirlpool stacked laundry center asks for one thing: remove power and let the control restart. If it returns, the control and its harness need checking.

Needs attention soonChecked November 2026

What does Whirlpool washer code F 22 mean?

F 22 can show on the washer half of an older stacked Whirlpool laundry center that prints error codes on some models. The code gives the owner one instruction, which is to remove power and let the control start over. It does not name a sensor, a valve or any other part, so the display alone cannot tell us what stopped the cycle. The washer stops and F 22 stays on until the power is cycled.

F 22 at a glance

Code
F 22
Appliance
Whirlpool washer
Applies to
Older Whirlpool stacked laundry center, washer half
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control that stopped mid-cycle and clears when power is removed

What you may notice with F 22

  • F 22 stays on the display
  • The washer stops partway through its cycle
  • The code comes back after a restart
  • The dryer above seems to behave normally

How the washer detects F 22

The control board decides when each step of the washer cycle begins and ends, and it halts the machine when something stops matching what it expects. F 22 is one of those halts. The guidance for it carries no part name, only an instruction to remove power.

Removing power for 2 to 5 minutes lets the control clear whatever it was holding and start again. If the stop was a single event, the washer runs normally afterward. If the same condition returns, the reset only cleared the display, and the cause remains in the control, in the wiring harness that carries its signals or in the power feeding the unit. A loose cord or a weak outlet can look the same as a control problem, so we check the plug and outlet too.

Likely causes of F 22

  • Control that stopped mid-cycle and clears when power is removed
  • Condition that returns after the reset, pointing to the control board and its harness
  • Loose cord or a weak outlet feeding the unit

Can you keep using the washer with F 22?

After one clean reset, yes, if the washer runs normally. If F 22 comes back, stop and leave the machine unplugged rather than cycling it repeatedly. Check that the cord and plug are undamaged and fully seated. If you see scorch marks or smell burning near the plug or outlet, leave the unit unplugged and do not use it until a technician has looked at it.

What you can safely check

  1. Stop the washer and pull the plug from the outlet; do not open any panel.
  2. Leave it out for at least 2 minutes, up to
  3. 3. Check that the cord and plug are undamaged, then plug in again.
  4. Close the lid or door, choose a short cycle and start it.
  5. If F 22 appears again, leave the machine and call us.

What our technician does for F 22

  • Trace the code from the control outward
  • Check the control board and its wiring harness
  • Test the outlet and cord connection

How to keep F 22 from coming back

  • Seat the plug fully and check the cord for damage
  • Avoid sharing the outlet with other heavy loads
  • Use a surge protector in storm season to guard the control board

Technical reference

Code
F 22
Appliance
Whirlpool washer
Control family
Older Whirlpool stacked laundry center, washer half
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F 22 questions

Is F 22 serious?

Not by itself. It is a general code with a power reset as the only owner step. If it comes back after a clean restart, it is worth having the control checked.

How long should the washer stay unplugged?

Between 2 and 5 minutes is enough for the control to reset. Longer does no harm, but it will not change the result if the underlying condition is still there.

Can the dryer on top keep running?

The two sections may share a cabinet and power cord, so test the dryer after the restart. If only the washer shows a code, tell us when you call.

Will F 22 clear by itself?

It can if it was a one-time stop. Unplugging for 2 to 5 minutes lets the control reset. If the code reappears, the cause is still present and the control or its harness needs checking.

What details should I give about F 22?

Tell us it is a stacked laundry center showing F 22, what the washer was doing when it stopped and whether the dryer section works. That helps us plan tests of the control.

Need help with F 22?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair