(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Top-Load Washer F0E0: Reset the Control First

F0E0 on a Whirlpool top-load HE washer comes with one instruction: remove power for 5 minutes. The display names no part, so a repeat after the reset needs a technician.

Needs attention soonChecked November 2026

What does Whirlpool washer code F0E0 mean?

F0E0 shows on Whirlpool top-load HE washers of the Cabrio and WTW family, such as the WTW5000DW, WTW5105HW, WTW7500GC and WTW8500DC, including older models that signal with flashing lights or a display code. The only direction given is to reset the control by removing power for 5 minutes. The display names no part or cause. The washer stops and shows F0E0. If a single reset clears it, the stop was likely a one-time event.

F0E0 at a glance

Code
F0E0
Appliance
Whirlpool washer
Applies to
Whirlpool top-load HE washers, Cabrio and WTW family
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control that halted and clears with a full power reset

What you may notice with F0E0

  • F0E0 appears and the washer stops
  • The cycle does not carry on
  • The code returns after the reset
  • Flashing lights on older models instead of a display code

How the washer detects F0E0

The control in a top-load HE washer manages each stage of the cycle and stops the machine when something does not match what it expects. F0E0 is one of those stops, and the instruction attached to it is a reset of 5 minutes without power.

That wait gives the control time to clear whatever it was holding, and the washer can then start from a clean state. A reset shows only whether the stop was a one-off. It does not reveal which circuit raised the code. If F0E0 returns, the cause is persistent and may sit in the control, in wiring that reaches the washer's loads or in power that drops at the plug or outlet. A technician follows the circuit from the control outward.

Likely causes of F0E0

  • Control that halted and clears with a full power reset
  • Recurring control or wiring condition if F0E0 returns
  • Loose plug or an outlet that drops power

Can you keep using the washer with F0E0?

After one full 5-minute reset, yes, if the washer runs normally. If F0E0 comes back, stop and arrange a visit instead of unplugging it again and again, which tells us nothing new. Check the cord and plug for damage. If the plug feels hot or you smell burning, keep the washer unplugged until a technician has checked it.

What you can safely check

  1. Stop the washer and pull the plug from the outlet; keep every panel closed.
  2. Leave it unplugged for 5 minutes.
  3. Plug it back in, close the lid and choose a cycle.
  4. If F0E0 comes back, stop and call us.
  5. Do not unplug and plug it in again and again.

What our technician does for F0E0

  • Trace the code from the control out to the washer loads
  • Check the control board and wiring
  • Test the plug and outlet for dropped power

How to keep F0E0 from coming back

  • Seat the plug fully and keep the cord free of damage
  • Use a surge protector during storm season to protect the control
  • Keep the outlet free of other heavy appliances

Technical reference

Code
F0E0
Appliance
Whirlpool washer
Control family
Whirlpool top-load HE washers, Cabrio and WTW family
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show F0E0

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

F0E0 questions

What does F0E0 mean on a Cabrio?

The display gives no part name. The one thing to try is to unplug the washer for 5 minutes, plug it in again and run a cycle.

Why exactly five minutes?

That is the wait given for resetting this control. A shorter wait may not let it clear, so give it the full time before judging the result.

My washer is old. Is a visit worth it?

It can be. We quote in writing before work, and if the age of the machine says a repair is poor value, we tell you directly.

Will F0E0 clear by itself?

It can if the stop was a single event. A full reset of 5 minutes lets the control start over. If the code returns, the cause remains, and the control and wiring need testing.

What should I share about F0E0 before the visit?

Give us your model, such as the WTW5105HW, what the washer was doing when F0E0 appeared and whether the 5-minute reset helped. That helps us plan the test.

Need help with F0E0?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair