(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Duet Washer F1 E1: Five-Minute Power Reset

F1 E1 on a Whirlpool front-load Duet or WFW washer comes with one instruction: cycle power to the control. No part is named, so it is a control-level code that a reset may clear.

Needs attention soonChecked November 2026

What does Whirlpool washer code F1 E1 mean?

F1 E1 appears on Whirlpool front-load washers of the Duet and WFW series, such as the WFW5620HW, WFW9150WW and WFW90HEFW, in both current and older generations. The guidance for it is only to cycle power to the control, which means the display does not name a sensor, valve or other part. The washer stops with F1 E1 showing. Because no part is named, we read it as a control-level code that a reset may clear.

F1 E1 at a glance

Code
F1 E1
Appliance
Whirlpool washer
Applies to
Whirlpool front-load washers, Duet and WFW series
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control that stalled and clears after power is removed

What you may notice with F1 E1

  • F1 E1 shows and the washer stops
  • No part or cause is named on the display
  • The cycle does not carry on by itself
  • The code may return soon after a reset

How the washer detects F1 E1

The control on a Duet or WFW washer runs every stage of the cycle and checks itself as it goes. When it reaches a state it cannot continue from, it halts the washer and prints a code. F1 E1 is one of those codes, and the only direction that comes with it is to cycle power to the control.

Pulling the plug for 5 minutes lets the control clear whatever it was holding. If the washer then starts normally, the stop was most likely a one-time event. If F1 E1 comes back, the reset has only hidden the cause, which may sit in the control, in a connection to it or in the power it receives. The display names no sensor or valve, so a technician traces the circuit from the control outward.

Likely causes of F1 E1

  • Control that stalled and clears after power is removed
  • Control or connection condition that returns after a reset
  • Power at the outlet or a loose plug

Can you keep using the washer with F1 E1?

After one clean reset, yes, if the washer runs normally. If F1 E1 returns, stop rather than keep unplugging the washer, since repeated resets show nothing new. Look at the plug and cord for damage. If you see heat or a burning smell near the outlet, leave the washer unplugged until it has been inspected.

What you can safely check

  1. Stop the washer and disconnect it by pulling its plug.
  2. Leave it unplugged for 5 minutes.
  3. Plug it back in and close the door.
  4. Select a cycle and start it.
  5. If F1 E1 comes back, stop and call us.

What our technician does for F1 E1

  • Test the control and its connections
  • Check the plug and outlet for steady power
  • Trace the circuit that raised the code

How to keep F1 E1 from coming back

  • Push the plug all the way into the outlet
  • Keep the cord free of damage and strain
  • Use a surge protector when storms are active

Technical reference

Code
F1 E1
Appliance
Whirlpool washer
Control family
Whirlpool front-load washers, Duet and WFW series
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F1 E1 questions

How long do I unplug a Duet for F1 E1?

Five minutes. Unplug it from the outlet, wait the full time without pressing buttons, plug it back in, close the door and start a cycle again.

Does F1 E1 mean the washer is finished?

No. The code names no part, and many washers carry on after a reset. If F1 E1 returns right away, we look at the control and its connections.

Will it lose my settings?

Possibly the current cycle, so select it again. The reset does not harm the washer, and if the code stays away you have lost nothing but a few minutes.

Is F1 E1 the same as F1E1?

They look alike, but they come from different washers. F1 E1 with a space belongs to front-load Duet and WFW models, while F1E1 without a space appears on other platforms. The 5-minute reset is common to both.

Will F1 E1 clear by itself?

A one-time stop may clear that way. Cutting power for 5 minutes gives the control a fresh start. If the code returns, the cause is still present and the control needs testing.

Need help with F1 E1?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair