(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Duet Washer F2 E2: Stopped Cycle Waits on a Power Reset

F2 E2 on a Whirlpool Duet or WFW front-load washer is a control-level stop. The direction is a 5-minute power reset, and the display names no sensor or part.

Needs attention soonChecked November 2026

What does Whirlpool washer code F2 E2 mean?

Owners of Whirlpool front-load washers in the Duet and WFW family, including the WFW5620HW, the WFW9150WW and the WFW90HEFW, may see F2 E2 when the washer halts a cycle. The direction for it is limited to a power reset of 5 minutes, and the display does not name any sensor or part. We therefore treat F2 E2 as a control-level stop. The drum does not carry on until power has been cycled.

F2 E2 at a glance

Code
F2 E2
Appliance
Whirlpool washer
Applies to
Whirlpool front-load washers, Duet and WFW family
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control stop that a full power reset can clear

What you may notice with F2 E2

  • F2 E2 appears and the drum stops
  • The washer waits until power has been cycled
  • Wet clothes remain inside the stopped drum
  • The same code can return after a reset

How the washer detects F2 E2

When a Duet or WFW washer meets a condition it cannot continue through, the control halts the cycle and displays a code. F2 E2 is one of those, and the guidance for it covers only a power reset of 5 minutes.

Because the display does not name a sensor or part, the code reads as a control-level stop. Cutting power lets the electronics clear fully and the washer start from a clean state. If the next cycle runs normally, the stop was probably a single event. If F2 E2 returns, the reset has only postponed it, and the cause may be in the control, in the wiring around it or in power that drops out at a loose plug or outlet. Testing is the only way to separate those.

Likely causes of F2 E2

  • Control stop that a full power reset can clear
  • Recurring condition in the control or its wiring
  • Loose plug or an outlet that drops out

Can you keep using the washer with F2 E2?

After one reset, you can keep using the washer if it finishes a cycle normally. If F2 E2 returns, stop and have it tested instead of repeating resets. Wet clothes left in the drum for days can turn musty, so once the washer works run a Drain & Spin, or take them out and wring or hang them while you wait.

What you can safely check

  1. Stop the washer and pull the plug; give it 5 minutes with no power.
  2. Plug it back in firmly.
  3. Close the door and start a normal cycle.
  4. If F2 E2 comes back, stop resetting and call us.

What our technician does for F2 E2

  • Test the control and its connections
  • Check the wiring to the control
  • Test the plug and outlet

How to keep F2 E2 from coming back

  • Seat the plug firmly and check it holds in the outlet
  • Keep the cord away from heat and sharp edges
  • Take wet clothes out soon if a cycle stops partway

Technical reference

Code
F2 E2
Appliance
Whirlpool washer
Control family
Whirlpool front-load washers, Duet and WFW family
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F2 E2 questions

Is F2 E2 an emergency?

No. The washer stops itself and waits. A 5-minute unplug is the one step to try, and your clothes are safe in the drum meanwhile.

Will the wet clothes be ruined?

No, but do not leave them for days. Once the washer works again, run a Drain & Spin or rinse so they do not turn musty.

What happens at the visit?

We read the washer, test the control and its connections, explain what we find in plain words, and give you a written price before we do anything.

Is F2 E2 the same as F2 E1?

They are neighbors with the same owner step. Both call for a 5-minute reset on a Duet or WFW washer, and neither names a part. Testing is what shows whether they come from the same cause.

Will F2 E2 clear by itself?

A single stray event can clear, because a full reset lets the control start clean. If the code returns, the cause is still there and the control needs to be tested.

Need help with F2 E2?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair