(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Laundry Tower Washer FAE1: Shipping Bolts Still Installed

FAE1 on the washer half of a Whirlpool laundry tower means the transport bolts were never removed. The drum cannot move freely, so the control stops the cycle and shows the code.

Maintenance reminderChecked November 2026

What does Whirlpool washer code FAE1 mean?

FAE1 appears on the washer section of a Whirlpool laundry tower or stacked laundry center when the shipping bolts are still in place. The bolts lock the drum in position while the unit travels, and they have to come out before the first wash. With them installed the drum is held rigid, so the control halts the cycle and displays FAE1. You see it on a newly delivered or recently moved unit, and the cure is an installation step, not a repair.

FAE1 at a glance

Code
FAE1
Appliance
Whirlpool washer
Applies to
Whirlpool laundry tower or stacked laundry center, washer section
Type
Maintenance reminder
Can you clear it yourself?
Usually, once the care step is done
Most likely cause
Transport bolts left in the back of the washer after delivery

What you may notice with FAE1

  • FAE1 on the display of a newly installed washer
  • The cycle stops almost as soon as it starts
  • Bolt heads visible on the back panel
  • Little or no drum movement when the washer tries to run

How the washer detects FAE1

On start-up the control turns the drum and watches how it responds. A free drum moves with a smooth, predictable pattern. When shipping bolts are still threaded through the back, the drum cannot swing on its suspension, so the control reads the movement as wrong and stops before any damage happens.

The bolts are only meant for transport. They keep the drum from knocking around inside the cabinet while the unit rides on a truck or a dolly. After they are out, the suspension takes over and the drum moves freely. That is why FAE1 shows up on a fresh install or after a move, and why it clears once the bolts are removed and the control is reset with a short power cycle.

Why FAE1 appears

  • Transport bolts left in the back of the washer after delivery
  • Packing blocks or foam not fully removed
  • Drum movement reading, only if every bolt is confirmed out

Can you keep using the washer with FAE1?

Do not run the washer with the shipping bolts in. The drum is locked solid, the cabinet can shake hard, and the parts that normally cushion the drum are not doing their job. Remove the bolts as the installation instructions show, fit the plugs, and reset the control. Once every bolt is out and the unit runs normally, it is fine to use. If FAE1 stays, stop and have it checked.

What you can safely check

  1. Stop the washer and unplug it before you reach behind the cabinet.
  2. Find the shipping bolts on the back and remove each one as the installation instructions show.
  3. Keep the plugs that come with the unit and fit them into the openings.
  4. Plug the washer in, then unplug it for 5 minutes to reset the control.
  5. Run a short cycle. If FAE1 shows after every bolt is out, call us.

What our technician does for FAE1

  • Confirm every shipping bolt and packing block is out
  • Check the drum for free movement
  • Inspect the installation, especially on a unit moved from another home
  • Test the drum movement reading if the code stays

How to keep FAE1 from coming back

  • Remove every shipping bolt and packing block before the first cycle on any new unit
  • Keep the bolts in a labeled bag in case you move the tower again
  • Ask the delivery crew to confirm the bolts are out, or check the back yourself
  • Refit the bolts as the manual shows before a move, then remove them again at the new home

Technical reference

Code
FAE1
Appliance
Whirlpool washer
Control family
Whirlpool laundry tower or stacked laundry center, washer section
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

FAE1 questions

Where do I find the shipping bolts on a laundry tower washer?

They sit at the back of the washer section and thread through the cabinet into the drum support. Your installation instructions show how many there are and where each one goes.

Should I keep the bolts after removing them?

Yes, if you might move the unit later, since they protect the drum in transit. Close the openings with the plugs from the installation hardware so the back stays sealed.

Does running a load with the bolts in do harm?

It can. The drum is held rigid and the cabinet may shake hard. If a cycle ran this way, stop, remove the bolts, and tell us if you hear grinding.

Is FAE1 a sign the washer is broken?

No, it is an installation message. The washer is telling you the drum is still locked for transport. Removing the bolts and resetting the control clears it in most cases, and nothing has to be replaced.

Will FAE1 go away on its own?

Not while the bolts are in. The drum stays locked, so the control keeps stopping the cycle. After the bolts are out, a short power cycle lets it clear. If it still shows, there may be another cause to check.

Something else going on with your washer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair