(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Washer Door Open Symbol: Door Will Not Lock

The Door Open symbol blinking on a Whirlpool washer means the door cannot lock. Clothing in the opening or soap residue near the latch can be the reason, and the cycle will not run until it locks.

Needs attention soonChecked November 2026

What does Whirlpool washer code Door Open mean?

Some Whirlpool washers show a blinking Door Open symbol, and the guidance behind it does not name a series. The message means the door is not locking. Something may be in the way, such as a piece of clothing caught in the opening or soap residue around the latch. Firm pressure on the door near the lock can let it close properly. Until the door locks, the washer will not start its cycle, and the symbol keeps blinking on the display.

Door Open at a glance

Code
Door Open
Appliance
Whirlpool washer
Applies to
Whirlpool washers with a door lock and a blinking door symbol
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Piece of clothing pinched between door and washer

What you may notice with Door Open

  • A door symbol blinks on the display
  • The cycle will not start while the symbol blinks
  • The door closes but the lock does not click
  • Clothing edges stick out near the latch

How the washer detects Door Open

A washer must be sure its door is shut and locked before it fills or spins. The control sends a signal to the door lock and then waits for a reply confirming the latch has closed.

When that reply does not come, the washer holds the cycle and blinks the Door Open symbol. A physical obstruction is the simplest reason: clothing pinched in the opening keeps the door from reaching the latch, and soap residue around the lock can stop it from seating. The same blinking happens if the lock itself does not report back, because the control cannot tell the difference between an obstruction and a lock that has stopped answering. That is why the checks start with the door area.

Likely causes of Door Open

  • Piece of clothing pinched between door and washer
  • Soap residue gathered around the door lock
  • Door not pushed fully shut
  • Door lock not responding to the control

Can you keep using the washer with Door Open?

Not until the door locks. The washer will not run its cycle with this symbol blinking, and you should never try to jam or bypass the lock to force it. Clear the opening, remove soap residue and press the door firmly near the lock. If the washer then runs normally, you can keep using it. If the symbol keeps returning, stop and let a technician test the lock.

What you can safely check

  1. Press Start/Pause to stop the cycle, then unplug the washer or turn off its breaker before you touch the door area.
  2. Look for clothing or soap residue around the opening and the latch, and clear it.
  3. Press firmly on the door near the lock.
  4. Plug in, touch Start/Pause, and see whether the symbol stops blinking.
  5. If it stays, touch and hold Power for at least three seconds. Call us if it returns.

What our technician does for Door Open

  • Test the door lock and its latch
  • Check the circuit that reports door position
  • Replace the lock if it fails to engage

How to keep Door Open from coming back

  • Check the door opening for stray clothing before you close it
  • Wipe soap residue from around the latch and gasket regularly
  • Close the door with a firm push until you feel it seat

Technical reference

Code
Door Open
Appliance
Whirlpool washer
Control family
Whirlpool washers with a door lock and a blinking door symbol
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Door Open questions

Why won't my washer door lock?

Clothing caught in the opening or soap residue around the latch is the common reason. Clear the area, press the door firmly near the lock and touch Start/Pause to try again.

What does holding Power do?

If the symbol stays, the guidance asks you to touch and hold Power for at least three seconds. That is the last owner step before you arrange service for the washer.

Can you replace a door lock?

Yes, if testing shows the lock needs it. We quote the price in writing before starting, cover the repair for 30 days on workmanship, and say plainly if an older washer is not worth the cost.

Will the symbol clear on its own?

Only if the cause was something simple, like a sleeve in the opening. Once the door can seat and the lock engages, the symbol should stop blinking when you press Start/Pause again.

What should I describe about the door when I phone?

Describe whether anything was pinched in the door, whether you pressed near the lock and tried holding Power. Give us your model name if you know it. That helps us bring the right lock.

Need help with Door Open?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair