(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Front-Load Washer Display Int: Cycle Paused or Canceled

Int on a Whirlpool Duet or WFW front-load washer is not an error. It shows that the cycle was paused or canceled while the washer winds down, and it can last 20 to 30 minutes.

Normal status, not a failureChecked November 2026

What does Whirlpool washer code Int mean?

Int is a status display on a Whirlpool front-load washer from the Duet and WFW family, including models such as the WFW5620HW and WFW90HEFW. It means the cycle was paused or canceled and the washer is winding down. The drum may need 20 to 30 minutes to stop spinning and drain, and Int stays lit during that time. When the washer has finished, the door can open and the display can be cleared. The method for clearing it varies by model.

Int at a glance

Code
Int
Appliance
Whirlpool washer
Applies to
Whirlpool Duet and WFW front-load washers
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
Cycle paused or canceled by pressing Pause/Cancel

What you may notice with Int

  • Int on the display after you press Pause or Cancel
  • The drum still turning or the pump running
  • The door locked for a while
  • Buttons that do not respond until the wind-down ends

How the washer detects Int

When you press Pause or Cancel, the washer does not simply stop in place. A drum full of wet clothes can be spinning quickly, and the tub can hold water. The control brings the drum to a stop in a controlled way and drains the water before it lets the door unlock.

While that happens, the display shows Int to tell you the cycle was interrupted. The wind-down can take 20 to 30 minutes, longer with a heavy load. Only once the drum is still and the water is gone does the control accept a new selection. Int is therefore a progress message, not a diagnosis. It becomes a concern only when it shows up on its own with nobody having paused or canceled anything.

Why Int appears

  • Cycle paused or canceled by pressing Pause/Cancel
  • Washer still spinning down and draining
  • Control waiting for input after the interruption

Can you keep using the washer with Int?

Yes, there is nothing to stop. Wait for the drum to finish spinning and draining, then clear the display and start a new cycle. Do not force the door while the drum moves or water remains inside. If Int appears by itself during normal runs, stop using the washer and have the door latch and power supply tested.

What you can safely check

  1. Do not force the door while the drum spins down, and unplug the washer only after the drum has stopped.
  2. Give the washer 20 to 30 minutes to stop and drain.
  3. Press Pause or Cancel twice, then press Power once, though the exact method varies by model.
  4. If Int stays, cut power for five minutes at the plug or breaker, then restore it.
  5. Start a new cycle, and call us if Int returns on its own.

What our technician does for Int

  • Check the door latch signal
  • Test the power supply to the control
  • Read why the cycle was interrupted when nobody paused it

How to keep Int from coming back

  • Pause or cancel only when needed, and give the washer the full wind-down before opening the door
  • Keep the washer plugged into a steady outlet so power dips do not interrupt cycles
  • Avoid overloading, since a heavy load takes longer to stop and drain
  • Check your manual for the clearing steps on your model so you are ready next time

Technical reference

Code
Int
Appliance
Whirlpool washer
Control family
Whirlpool Duet and WFW front-load washers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Int questions

Does Int mean my washer is broken?

No. It means the cycle was paused or canceled and the washer is stopping safely. Wait for the drum to finish spinning and draining, then clear the display and begin again.

Why does the washer take so long to stop?

The drum may be spinning at speed with a heavy load and water inside. It slows, then pumps out, and that can take 20 to 30 minutes. The door stays locked until the process is done.

How do I clear Int?

On most models press Pause or Cancel twice and then Power once. Some work a little differently, so check your manual. If it does not clear, a short power reset at the outlet should do it.

Is Int the same as PF?

No. Int means the cycle was paused or canceled, most likely by you. PF means the washer lost power during the cycle. Both can stop a wash, but Int is a normal wind-down and PF comes from an interruption in power.

Why does Int come back by itself?

A code that returns with nobody pausing the cycle suggests the washer is reading an interruption, such as a door, power or control signal. That is worth testing, because the washer is deciding on its own to stop.

Something else going on with your washer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair