Whirlpool Top-Load Washer Code oL: The Tub Is Overloaded
oL on an older Whirlpool top-load HE washer means the load is too large for the washer to run a full cycle. Taking out some items and spreading the rest clears it.
What does Whirlpool washer code oL mean?
oL on an older Whirlpool top-load HE washer from the Cabrio and WTW family tells you the load is too large. The washer is overloaded, and the control will not run a full cycle with that much weight in the basket. An overloaded tub also goes out of balance easily, so the two problems may arrive together. The display shows oL, the cycle stops, and the clothes need to be lightened or rearranged before you try again.
oL at a glance
- Code
- oL
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Cabrio and WTW top-load HE washers
- Type
- Maintenance reminder
- Can you clear it yourself?
- Usually, once the care step is done
- Most likely cause
- Basket packed past its working capacity
What you may notice with oL
- oL on the display and the cycle stopped
- A basket packed to the top with clothes
- Heavy, soaked bedding in the tub
- A washer that struggles to turn the load
How the washer detects oL
At the start of a cycle, the washer turns the basket and senses how much weight it must move. The motor and the sensing circuit give the control a reading of the load. If the load is heavier than the washer is designed to handle, the control refuses to run a full cycle and shows oL.
A tub that is packed past its working capacity is the obvious cause. Bulky items such as comforters add to it, because they soak up water and weigh much more once wet. A load bunched on one side can also read as heavier than it is. Because an overloaded basket tends to go out of balance, OFb may follow if the clothes are not lightened and spread out. A modest load that still brings oL points to the weight sensing instead.
Why oL appears
- Basket packed past its working capacity
- Bulky items such as comforters absorbing a lot of water
- Load bunched unevenly, making the weight read higher
- Weight sensing, if a modest load still brings oL
Can you keep using the washer with oL?
Yes, once you take out some items and spread the rest loosely, you can run the washer again. Use Drain & Spin first if water is sitting in the tub. Do not reach into a moving basket. If a small load still brings oL, stop using the washer and have the weight sensing and suspension checked.
What you can safely check
- Cancel the cycle with Start or by disconnecting the power cord, and wait for the basket to stop.
- Run a drain-only cycle if the tub holds water.
- Take out some items so the clothes sit loosely, and rearrange them evenly.
- Choose Bulky or Heavy Duty, and use Drain & Spin if you only need the water out.
- If a small load still brings oL, call us.
What our technician does for oL
- Test the weight sensing
- Check the suspension
- Confirm the washer is level
How to keep oL from coming back
- Load clothes loosely so they move freely and sit below the top of the wash plate
- Wash comforters and bulky bedding in smaller portions
- Do not press extra items into a full basket to finish in one load
- Spread wet items around the plate before closing the lid
Technical reference
- Code
- oL
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Cabrio and WTW top-load HE washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
oL questions
How full is too full?
Clothes should move freely and not be packed above the wash plate. Bulky bedding soaks up water and weighs far more wet than dry, so run it in smaller portions.
Is oL the same as OFb?
No. oL means too much weight, while OFb means the weight is uneven. They overlap in the fix, which is to lighten and rearrange the load, but the displays name different things.
Can I pause the cycle and fix the load?
Yes. Press Start to pause, wait for the lid to unlock and rearrange. Never reach in while the basket is still moving. Wait until it has fully stopped.
Will oL clear by itself?
No. The washer keeps stopping until the load is lighter. Remove some items, spread the rest evenly and restart. If oL appears again with a small load, the weight sensing or the suspension is probably reading wrong and should be tested.
Can an overloaded tub hurt the washer?
Running it overloaded strains the motor, the suspension and the basket. That is why the control stops the cycle. Lightening the load protects the washer and also gives cleaner, better rinsed clothes.
Something else going on with your washer?
We trace the cause in your home first and write the price down before any part is swapped.