(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Front-Load Washer LoC or LC: Control Lock Is Switched On

LoC, or LC on some models, is not an error on a Whirlpool Duet or WFW front-load washer. It reminds you the Control Lock is on, so the buttons do nothing until you turn it off.

Normal status, not a failureChecked November 2026

What does Whirlpool washer code LoC mean?

LoC, or LC on some models, is not an error on a Whirlpool front-load washer from the Duet and WFW family, such as the WFW5620HW or WFW9150WW. It reminds you that the Control Lock is active. While the lock is on, the buttons do nothing, and the display shows the code whenever you press one. You can still touch Start to pause a running cycle or Power to turn the washer off. Nothing is broken, since the controls are only waiting for you to unlock them.

LoC at a glance

Code
LoC
Appliance
Whirlpool washer
Applies to
Whirlpool Duet and WFW front-load washers
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
Control Lock turned on, on purpose or by a stray touch

What you may notice with LoC

  • LoC or LC on the display when you press a button
  • Cycle buttons that seem dead when pressed
  • Start and Power still working as usual
  • A countdown on the display when you hold the Control Lock button

How the washer detects LoC

Control Lock is a feature, not a failure. When it is on, the control ignores most button presses so a curious child or an accidental touch cannot change a running cycle. Each time a locked button is pressed, the display answers with LoC, or LC on some models, to remind you why nothing happened.

Two buttons still work while the lock is on. Start can pause a cycle that is running, and Power can turn the washer off. That keeps the washer safe to stop in an emergency. To turn the lock off, you touch and hold the Control Lock button for about three seconds. The display counts down 3, 2, 1 and then shows LoC or LC as the lock changes state. The same sequence turns it on again.

Why LoC appears

  • Control Lock turned on, on purpose or by a stray touch
  • Control Lock set by a child or while cleaning the panel

Can you keep using the washer with LoC?

Yes, the washer is working normally. Hold the Control Lock button for about three seconds to turn the lock off, then choose your cycle as usual. You do not need to stop using the washer or unplug it for this code. Only if the keys stay unresponsive after unlocking and a power reset should the keypad and control be tested.

What you can safely check

  1. Nothing needs to be shut off for this code, so just leave the cycle as it is and keep clear of the door.
  2. Touch and hold the Control Lock button for about three seconds.
  3. Watch the display count down 3, 2, 1 and then show LoC or LC as the lock changes state.
  4. Press a cycle button to confirm the controls respond again.
  5. If the lock will not release, unplug the washer for five minutes and try again, and call us if the keys stay dead.

What our technician does for LoC

  • Test the keypad
  • Check the control for stuck inputs
  • Confirm the lock setting is stored correctly

How to keep LoC from coming back

  • Keep the panel clean and dry so wet cloths do not trigger the Control Lock button
  • Turn the lock on only when you want it, such as around small children
  • Remember the three-second hold so you can switch it off quickly
  • Wipe the panel with the washer idle, not mid-cycle

Technical reference

Code
LoC
Appliance
Whirlpool washer
Control family
Whirlpool Duet and WFW front-load washers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

LoC questions

Why do my buttons do nothing?

The Control Lock is probably on. The display shows LoC or LC when you press a key. Holding the Control Lock button for about three seconds turns it off and brings the keys back.

Is LoC a sign of a problem with the control?

No. It is a normal reminder, built in so that children or stray touches cannot change a running cycle. The washer is working exactly as designed.

Can I still stop a cycle with the lock on?

Yes. Start still pauses the cycle, and Power turns the washer off. Everything else stays locked until you hold the Control Lock button again and release it.

Will LoC go away by itself?

No. The Control Lock stays on until you turn it off with the three-second hold. It also survives a normal cycle. If the keys still do nothing after you unlock the panel and reset the power, then the keypad or control needs a test.

Is LoC the same as LC?

Yes. Some models show LoC and others show LC for the same thing, the Control Lock reminder. The way to turn it off is identical on both, so follow the steps for your washer.

Something else going on with your washer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair