(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Laundry Tower Washer F3E8: General Temperature Sensor Alert

F3E8 on a Whirlpool laundry tower washer section is a temperature sensor alert that does not name which sensor. A power reset is the only owner step the brand offers.

Needs attention soonChecked November 2026

What does Whirlpool washer code F3E8 mean?

On the washer section of a Whirlpool laundry tower or stacked laundry center, F3E8 refers to a temperature sensor. It is a plainer alert than F3E7, which names the wash temperature sensor specifically. The code appears on the display and the washer may stop or refuse to run a cycle. The only owner step offered is a power reset, and no model number is named for this code.

F3E8 at a glance

Code
F3E8
Appliance
Whirlpool washer
Applies to
Whirlpool laundry tower and stacked laundry center washer section
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A temperature sensor circuit in the washer section

What you may notice with F3E8

  • F3E8 shows on the display of the washer section
  • The washer may stop mid-cycle or decline to start
  • Water temperature may seem off during fill

How the washer detects F3E8

A laundry tower washer section blends hot and cold water to hit the temperature each cycle needs, and one or more sensors report back how that is going. The control treats those readings as a safety net: if a sensor signal is missing or outside what it can believe, the control will not guess.

F3E8 is the general form of that alert. It says a temperature sensor is a problem but does not say which one. That is unlike its neighbor code, which names the wash temperature sensor directly. Since the display gives no further detail, the work falls to testing: we read each sensor and its wiring, then compare what the control is receiving with what the washer should be producing during fill and wash.

Likely causes of F3E8

  • A temperature sensor circuit in the washer section
  • Wiring between the sensor and the control
  • The control's reading of the sensor signal

Can you keep using the washer with F3E8?

Try one reset and a single short cycle. If F3E8 returns, stop using the washer section until it is tested. A control that cannot trust its temperature reading may run a cycle at the wrong heat, which can ruin loads and strain the machine. There is no gas hazard, but unplug the tower if you find water leaking.

What you can safely check

  1. Stop the cycle and unplug the laundry tower for 5 minutes to reset the control.
  2. Restore power and confirm both water valves are fully open.
  3. Look behind the tower for kinked supply hoses.
  4. Run a short cycle.
  5. If F3E8 returns, call us so we can test the temperature circuits.

What our technician does for F3E8

  • Identify which temperature sensor on the washer section is reporting
  • Test that sensor and the wiring back to the control
  • Read the control's temperature value during a cycle

How to keep F3E8 from coming back

  • Keep supply hoses free of kinks and sharp bends behind the tower
  • Check the hose connections for slow drips, which can reach wiring behind the cabinet

Technical reference

Code
F3E8
Appliance
Whirlpool washer
Control family
Whirlpool laundry tower and stacked laundry center washer section
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F3E8 questions

Is F3E8 the same as F3E7 on a tower?

F3E7 names the wash temperature sensor, while F3E8 refers to a temperature sensor in general. We narrow it down by testing the individual circuits on the washer section instead of guessing from the code alone.

Is it safe to keep using the washer with F3E8?

Try one reset. If the code returns, the control cannot trust its temperature reading, so it is better to stop using the washer and have it checked than to keep running cycles with unreliable readings.

Will a reset fix F3E8?

It can clear a one-time glitch. If it comes back, a circuit needs testing and we tell you the price in writing first, with a 30-day workmanship warranty on the repair we complete.

Which sensor does F3E8 mean?

The display does not say. The code refers to a temperature sensor on the washer section without naming it, so we test the circuits one by one and tell you which one the control is complaining about.

Which details help narrow down F3E8?

Tell us it is a laundry tower, whether the washer stopped or refused to start, and what the 5-minute reset did. If you changed the hoses recently, mention that as well.

Need help with F3E8?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair