Whirlpool Washer F3E3: Air Inlet or Inlet Temperature Problem Explained
F3E3 on a Whirlpool washer points to the air inlet on an all-in-one washer-dryer or to the inlet temperature sensor on a laundry tower. Older top-loads give only a power reset.
What does Whirlpool washer code F3E3 mean?
F3E3 appears on three kinds of Whirlpool washer. On an all-in-one washer-dryer such as the WFC8090GX, it points to the air inlet function, so washing still works while drying will not run. On a laundry tower, the washer section reports the water inlet temperature sensor. On an older top-load HE washer (Cabrio or WTW series with display or blink codes), the only guidance is a power reset and no part is named. That older top-load is still in many homes, and we repair it.
F3E3 at a glance
- Code
- F3E3
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool WFC8090GX, laundry tower and older top-load washers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Air inlet circuit on an all-in-one washer-dryer
What you may notice with F3E3
- F3E3 shows on the display and the cycle may stop
- On an all-in-one unit, washing runs but drying does not
- A tower may refuse to fill at the expected temperature
How the washer detects F3E3
Two different parts of a Whirlpool laundry setup are involved here. On an all-in-one washer-dryer, the drying side needs air drawn in through an inlet. If the control does not see that air path working, it limits drying but lets the wash side continue, which is why a wash may finish while the dry will not run.
On a laundry tower, the washer section measures the temperature of incoming water with a sensor at the inlet. The control compares that reading to the cycle's needs. When the sensor reports something unusable, F3E3 appears. Older top-load HE models with display or blink codes give no named part at all, only the reset, so those get tested at the control and wiring level.
Likely causes of F3E3
- Air inlet circuit on an all-in-one washer-dryer
- Water inlet temperature sensor on a laundry tower
- A control reading on an older top-load that a reset may clear
Can you keep using the washer with F3E3?
On an all-in-one washer-dryer you can keep using the wash cycles while drying is unavailable, since the code limits the dry function. On a tower or older top-load, try one reset and a short cycle. If F3E3 returns, stop and have it checked. There is no gas or heat hazard from this code, but unplug the washer if you find leaking water.
What you can safely check
- Stop the cycle and pull the plug before reaching near the hoses.
- Wait at least 5 minutes, then plug the washer back in.
- On a laundry tower, confirm the hot hose is on the hot inlet and the cold hose on the cold inlet.
- Check that both water valves are fully open.
- On an all-in-one unit, note whether washing runs while drying does not. If F3E3 returns, call us.
What our technician does for F3E3
- Test the air inlet path and circuit on all-in-one units
- Read the inlet temperature sensor and wiring on a laundry tower
- Check the control reading on an older top-load
How to keep F3E3 from coming back
- Keep the air inlet area of an all-in-one unit clear of lint and stored items
- Confirm hose placement after any move so hot and cold stay on the correct inlets
Technical reference
- Code
- F3E3
- Appliance
- Whirlpool washer
- Control family
- Whirlpool WFC8090GX, laundry tower and older top-load washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
F3E3 questions
Can I still wash with F3E3 on an all-in-one washer-dryer?
The wash function should run, but the dry function will not. Use the unit as a washer only until we check the air inlet circuit, and tell us which cycles still work when you call.
What does F3E3 mean on a laundry tower?
The washer section reports the water inlet temperature sensor. Make sure the hoses are not swapped, reset the power for 5 minutes, and schedule service if the code returns, since the sensor circuit then needs testing.
My older top-load shows F3E3. Is it worth fixing?
These older top-loads remain in plenty of homes, and we work on them regularly. We test first, give a written price, and tell you plainly when repair makes little sense for the age.
Will F3E3 go away on its own?
A power reset may clear a one-time glitch. If the air inlet, sensor or control has a real problem, the code returns, and we need to test it rather than keep resetting the washer.
Does the older top-load need a part replaced for F3E3?
Not necessarily. The guidance for that model names no part, so we test the control and wiring first. We replace something only after the test shows which circuit is causing the code.
Need help with F3E3?
We trace the cause in your home first and write the price down before any part is swapped.