Whirlpool Washer Code F8E6: Water Detected, or No Hot Water on a Top-Load
F8E6 reports water detected on a Whirlpool laundry tower washer section. On top-load HE washers it can mean the lid was opened during soak or that no hot water was detected.
What does Whirlpool washer code F8E6 mean?
F8E6 shows up on two kinds of Whirlpool washer. On the washer section of a laundry tower, it reports that water has been detected, meaning water where the control does not expect it. On top-load HE washers, including the Cabrio and WTW series and older display-code models, the meaning depends on the model: the lid was opened during the soak cycle, or no hot water was detected, often because the hot and cold hoses are reversed. In both cases the cycle stops with the code showing.
F8E6 at a glance
- Code
- F8E6
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool laundry tower washer section and top-load HE washers
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- Hot and cold inlet hoses reversed, or the hot supply not reaching the washer
What you may notice with F8E6
- F8E6 appears on the display and the cycle stops
- On a top-load, the lid may have been lifted during soak
- The wash water may stay cold when warm was selected
How the washer detects F8E6
The same code is read in two separate ways. On a laundry tower, the washer section has a circuit that senses water, and F8E6 reports that it found water where the control did not expect any. On a top-load HE washer, the control watches the lid during the soak stage and also checks that hot water is arriving when a cycle asks for it.
A lid lifted during soak makes the control stop to protect the person reaching in, so closing it often resumes the cycle. Missing hot water is a different story: the control senses that the incoming water is cold when it asked for warm, which is how reversed hoses show themselves. Because the two readings come from different parts, we confirm your washer type before testing the lid circuit, the hot supply or the sensing circuit.
Likely causes of F8E6
- Hot and cold inlet hoses reversed, or the hot supply not reaching the washer
- The lid switch or lid position during the soak stage on top-load models
- The water sensing circuit on the tower washer section
- The main control reading, once those are ruled out
Can you keep using the washer with F8E6?
Close the lid, correct the hoses if they are swapped and try one cycle. If F8E6 returns, stop using the washer until it is tested. Never defeat a lid switch or hold the lid down to keep a cycle going. If you see water where it should not be on a tower, unplug it and close the faucets right away.
What you can safely check
- Stop the cycle and unplug the washer, then close the lid fully on a top-load model and see whether it resumes.
- Confirm the hot line sits on the hot inlet and the cold line on the cold inlet, and that both faucets are open.
- Cut power to the washer for five minutes, then restore it.
- Start a short cycle. If F8E6 returns, call us.
What our technician does for F8E6
- Confirm the hot supply reaches the washer
- Test the lid switch and its position circuit on top-loads
- Test the water sensing circuit on a tower
How to keep F8E6 from coming back
- Keep the lid closed during soak and avoid reaching in while the drum is moving
- Mark the hot and cold hoses so they cannot be crossed when the washer is moved or reinstalled
Technical reference
- Code
- F8E6
- Appliance
- Whirlpool washer
- Control family
- Whirlpool laundry tower washer section and top-load HE washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
F8E6 questions
Why does a top-load washer show F8E6 during soak?
Some models treat an open lid during the soak stage as a reason to stop. Closing the lid resumes the cycle. If the lid is closed and the code persists, we check the lid position circuit.
Can I tell if my hot water is actually reaching the washer?
Run the hot tap nearby until it warms, then check that the hose at the washer is warm too. A cold hot-side hose suggests a supply or reversed-hose problem rather than the washer.
Will resetting the washer clear F8E6?
A five-minute power reset clears a one-time glitch. If the hoses are reversed or hot water is missing, the code returns on the next cycle, and then a visit is the sensible next step.
Is it safe to lift the lid during soak?
The washer stops when you do, to protect your hands. Closing the lid lets some models resume, but wait until the drum is fully still before reaching in, and never hold the lid switch down.
How does F8E6 on a tower differ from a top-load?
A tower's washer section reports water detected where none was expected, while a top-load reports a lid or hot-water problem. We confirm the washer type before choosing which circuit to test.
Need help with F8E6?
We trace the cause in your home first and write the price down before any part is swapped.