(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Stacked Laundry Center Washer F 23: Reset and Retry

F 23 on the washer side of an older Whirlpool stacked laundry center comes with a power reset as the only owner step. A repeat points to the control or its connections.

Needs attention soonChecked November 2026

What does Whirlpool washer code F 23 mean?

F 23 is one of the codes older Whirlpool stacked laundry centers show on the washer side. The owner guidance is limited to a power reset, and nothing in it ties F 23 to a particular part, so we read it as a control-level stop and not as a verdict on any one part. On the display you see F 23 and the washer does not carry on. Many of these older units keep working after a reset, so a return of the code is what tells us a visit is needed.

F 23 at a glance

Code
F 23
Appliance
Whirlpool washer
Applies to
Older Whirlpool stacked laundry center, washer side
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Momentary control lockup that a reset clears

What you may notice with F 23

  • F 23 shows on the display
  • The washer does not carry on with the cycle
  • The code is gone after a reset, then returns
  • The washer side stops but the unit is otherwise quiet

How the washer detects F 23

The washer side of a stacked laundry center is run by a control that steps through fill, wash, drain and spin. When it detects something it cannot work through, it halts and prints a code. For F 23 the only direction is a power reset, with no part named.

That means the control cannot tell us, or the owner, what it saw. A reset of 2 to 5 minutes clears a momentary lockup and the cycle can run again. If F 23 returns, the cause is persistent and lies somewhere the control reaches: its own board, the wiring connections or the power feeding it. An outlet shared with other appliances can occasionally dip and upset a control, so power quality is part of what we look at.

Likely causes of F 23

  • Momentary control lockup that a reset clears
  • Control board or connection problem if F 23 returns after the reset
  • Power quality at an outlet shared with other appliances

Can you keep using the washer with F 23?

Yes, after one reset if the washer runs normally. If F 23 returns, stop using the washer and leave it unplugged rather than repeating resets, which do not fix a persistent cause. Check the plug and cord for damage. If you notice heat, a burning smell or sparking at the plug or outlet, keep the unit unplugged and have it inspected before any further use.

What you can safely check

  1. Stop the washer and unplug it; leave every panel closed.
  2. Let it rest for 2 to 5 minutes.
  3. Push the plug fully back into the outlet.
  4. Make sure the lid or door is shut and start a short cycle.
  5. If F 23 is still on the display, stop there and call us.

What our technician does for F 23

  • Check the control board and its connections
  • Test the washer wiring on site
  • Check the outlet for stable power

How to keep F 23 from coming back

  • Plug the unit directly into a good outlet
  • Avoid running other heavy appliances on the same outlet
  • Use a surge protector during storm season, since power surges can upset an older control

Technical reference

Code
F 23
Appliance
Whirlpool washer
Control family
Older Whirlpool stacked laundry center, washer side
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F 23 questions

What should I do first when F 23 shows?

Unplug the washer for 2 to 5 minutes, plug it back in and try a short cycle. That reset is the only owner step for this code.

Does F 23 mean the whole laundry center is dead?

No. It is a stop on the washer side, and many units go on working after a reset. A repeat is what tells us a repair visit is needed.

Why can't you tell me the cause by phone?

Because the code names no part. We have to look at the control and the washer's circuits in person, and we give you a written price first.

Will F 23 go away by itself?

Possibly, if it was a single stop. A reset of 2 to 5 minutes lets the control start clean. If the code returns, the cause is still present and needs a technician to find it.

What should I note before calling about F 23?

Tell us it is a stacked laundry center showing F 23, what stage the cycle was in and whether the code came back after your reset. That helps us decide where to start.

Need help with F 23?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair