(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Top-Load Washer Cycle Complete Light On: The Wash Is Done

When Cycle Complete glows on your Whirlpool Cabrio or WTW top-loader, the wash has ended; the light stays on until the lid is opened or Cancel is pressed, and it is no error.

Normal status, not a failureChecked November 2026

What does Whirlpool washer code Cycle Complete Light On mean?

A Whirlpool top-load HE washer in the Cabrio and WTW style, the WTW5000DW or WTW8500DC for example, lights Cycle Complete to say precisely what it says: the wash is over. Older machines of this kind remain in many laundry rooms. The light stays on until the lid is opened or Cancel is pressed. Taking the load out promptly gives the best results. This is a status light and not an error code.

Cycle Complete Light On at a glance

Code
Cycle Complete Light On
Appliance
Whirlpool washer
Applies to
Whirlpool Cabrio and WTW top-load HE washers, Cycle Complete light
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
The wash cycle ended normally

What you may notice with Cycle Complete Light On

  • The Cycle Complete light is lit on the panel
  • The drum has stopped turning and is quiet
  • The load inside is wet and ready to come out

How the washer detects Cycle Complete Light On

At the end of a wash, the control has nothing more to do, so it switches on the Cycle Complete light to say the load is ready. No sensor stands behind the light other than the control's own knowledge that it finished the program you chose.

The light stays on until something clears it. Opening the lid does, because that tells the control you have seen the finished load. Pressing Cancel does too, so you can turn it off without lifting the lid. A small load can finish sooner than you expect, since the washer adjusts its cycle to the size of the load. The light itself is a status signal and no error. A problem exists only if cycles end far too early or the light stays on after the lid is opened.

Why Cycle Complete Light On appears

  • The wash cycle ended normally
  • The load sitting in the drum afterward
  • The light not yet cleared by lifting the lid or pressing Cancel
  • A small load finishing sooner than expected

Can you keep using the washer with Cycle Complete Light On?

Yes, nothing is wrong with the washer when this light appears. Take the load out promptly so clothes do not sit wet, then use the washer as normal. Only a cycle that ends far too early, or a light that will not clear after the lid is opened, calls for a check of the lid switch and control.

What you can safely check

  1. The washer needs no power step, because it has simply finished.
  2. Lift the lid, which turns the light off.
  3. Take the wet load out soon.
  4. If you prefer, press Cancel and the light clears while the lid stays shut.
  5. Leave the lid up for a while to air the drum; if cycles end far too early or the light stays on after the lid opens, contact us.

What our technician does for Cycle Complete Light On

  • Test the lid switch and the control if the light stays on after the lid opens
  • Test the washer if cycles end far too early

How to keep Cycle Complete Light On from coming back

  • Empty the washer soon after the light comes on, especially in warm, humid Florida weather.
  • Leave the lid up after unloading so the drum can air out and stay fresh.

Technical reference

Code
Cycle Complete Light On
Appliance
Whirlpool washer
Control family
Whirlpool Cabrio and WTW top-load HE washers, Cycle Complete light
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show Cycle Complete Light On

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

Cycle Complete Light On questions

Has something gone wrong when this light comes on?

No. It lights once the wash is done and stays on until you lift the lid or press Cancel. All it says is that the load is ready to be taken out.

Why unload quickly?

The guidance recommends removing the load promptly for the best results. Wet laundry sitting in the drum picks up odor and wrinkles while it waits.

Do you work on older Cabrio washers?

Yes, including ones long past their warranty. We test first, give the price in writing before work, and say plainly when a repair is not worth it.

Why did the light come on sooner than I expected?

The washer adjusts a cycle to the size of the load, so a small load can finish earlier. If normal loads end far too early, that is worth having tested.

Must I clear the light before the next wash?

Lifting the lid or pressing Cancel clears it, and starting the next cycle normally involves one of those steps anyway. A light that refuses to clear after the lid opens points to the lid switch.

Something else going on with your washer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair