Whirlpool Top-Load Washer Display Lid: Lid Opened During the Cycle
Lid on an older Whirlpool top-load HE washer is a message, not a failure. It means the lid was opened mid-cycle, and closing it clears the display unless the lid stayed open about 10 minutes.
What does Whirlpool washer code Lid mean?
Lid on the display of an older Whirlpool top-load HE washer from the Cabrio and WTW family is a message and not a failure. It tells you the lid was opened during the cycle. Close the lid and the display clears. If the lid stays open longer than 10 minutes, the cycle resets and the tub drains. In that case, start over. Do not add more detergent, since the clothes are already wet with water and detergent from the first start.
Lid at a glance
- Code
- Lid
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Cabrio and WTW top-load HE washers
- Type
- Normal status, not a failure
- Can you clear it yourself?
- Yes, it is a normal message or setting
- Most likely cause
- Lid opened during a cycle
What you may notice with Lid
- Lid on the display during a cycle
- The washer paused with water in the tub
- A tub that drained after the lid sat open
- Lid showing even though the lid is closed
How the washer detects Lid
A switch near the lid tells the control whether the lid is closed. While a wash, rinse or spin is running, the control expects that switch to stay closed. When the lid lifts, the signal changes and the washer pauses. The display shows Lid so you know why nothing is moving.
The washer waits for you. If the lid is closed again within 10 minutes, the cycle picks up where it left off. If the lid stays open longer, the control assumes you walked away, cancels the cycle and pumps the water out of the tub. That is a safeguard, so a full tub is never left sitting. When Lid shows with the lid shut, the switch is not reporting the closed lid, and it needs testing.
Why Lid appears
- Lid opened during a cycle
- Lid left open longer than 10 minutes, resetting the cycle
- Lid switch not registering a closed lid
Can you keep using the washer with Lid?
Yes, there is nothing wrong with the washer when Lid appears because the lid was opened. Close it and let the cycle continue, or start over if the water drained. Never reach into a basket that is still turning. If Lid shows with the lid fully closed, the switch may not be registering, and the washer should be checked.
What you can safely check
- Make sure the basket has stopped turning before you reach in.
- Close the lid fully and wait for the display to clear.
- If the washer drained after the lid stayed open, start the cycle over.
- Do not add more detergent, since the clothes already have it.
- If Lid shows with the lid closed, call us.
What our technician does for Lid
- Test the lid switch and its wiring
- Check lid alignment at the switch
- Clean the switch area of residue
How to keep Lid from coming back
- Keep the lid closed from Start until the cycle ends
- Add forgotten items only after you pause and the basket has stopped
- Wipe the lid and switch area so detergent and lint do not build up
- Close the lid with care so the switch lines up each time
Technical reference
- Code
- Lid
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Cabrio and WTW top-load HE washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
Lid questions
Does Lid mean something broke?
No. It simply tells you the lid is open. Close it and the cycle resumes, unless the lid stayed open past 10 minutes, in which case the cycle resets and starts over.
Why did my washer drain by itself?
After the lid has been open about 10 minutes, the washer cancels the cycle and pumps out the water. This prevents a full tub from sitting unattended with the lid up.
What if Lid shows while the lid is closed?
That suggests the lid switch is not reporting properly, perhaps because of dirt, a misaligned lid or the switch itself. We would test the switch and its wiring and quote before any part.
Do I need to add detergent again after the lid stayed open?
No. The clothes are already wet with water and detergent from the first start. Adding more can cause too many suds. Simply start the cycle over and let the washer fill again with the original dose.
Is Lid the same as LdL?
No. Lid says the lid was opened during the cycle. LdL says the lid lock did not engage. They sound similar, but Lid is a message about the lid position and LdL is a lock code, so the checks differ.
Something else going on with your washer?
We trace the cause in your home first and write the price down before any part is swapped.