Whirlpool Top-Load Washer Code HC: Hot and Cold Hoses Swapped
HC on an older Whirlpool top-load HE washer means the hot and cold inlet hoses are connected the wrong way around. Swapping them back clears it, and the washer otherwise runs.
What does Whirlpool washer code HC mean?
HC on an older Whirlpool top-load HE washer from the Cabrio and WTW family tells you the hot and cold inlet hoses were installed in reverse. The code appears at the end of the wash cycle. The cold line feeds the hot inlet and the hot line feeds the cold inlet. The washer completes its work, but the water temperatures were not the ones you chose, so washing results can disappoint. It is an installation matter, and switching the hoses clears it.
HC at a glance
- Code
- HC
- Appliance
- Whirlpool washer
- Applies to
- Whirlpool Cabrio and WTW top-load HE washers
- Type
- Maintenance reminder
- Can you clear it yourself?
- Usually, once the care step is done
- Most likely cause
- Hot hose on the cold inlet and cold hose on the hot inlet
What you may notice with HC
- HC on the display when the cycle ends
- Warm loads that came out cold or hot loads that felt lukewarm
- Hoses attached opposite to the red and blue marks
- No leak and no stalled cycle
How the washer detects HC
Sensors at the inlet valves track the temperature of the water entering through each hose during the cycle. The control knows which valve is supposed to carry hot water and which should carry cold. If the hot valve keeps receiving cold water and the cold valve receives hot, the readings disagree with what the control expects.
The washer does not stop for this. It finishes the cycle and then shows HC to report that the hoses look reversed. Because the water it used was not the temperature you selected, the wash may be cooler or hotter than intended. Nothing inside the washer has failed in the usual case. The hoses at the back are simply on the wrong inlets, and switching them puts the readings back in order.
Why HC appears
- Hot hose on the cold inlet and cold hose on the hot inlet
- Wall faucets labeled or plumbed backwards
- Temperature reading at the inlet valves, only if the hoses are already correct
Can you keep using the washer with HC?
Yes, the washer can keep running while you sort out the hoses, because HC is an installation warning and the cycle completes. Results will not match the temperature you picked, though, so swap the hoses soon. After switching them and checking for drips, run another cycle. If HC remains with correct hoses, have the wall lines and valves tested.
What you can safely check
- Stop the washer, unplug it and turn off both water supplies at the wall.
- Swap the hoses so the hot line goes to the hot inlet and the cold line to the cold inlet.
- Tighten the fittings by hand, open the faucets and look at each connection for drips.
- Run another cycle to see whether HC is gone.
- If HC remains with correct hoses, call us.
What our technician does for HC
- Confirm which wall line is truly hot
- Check the inlet valve temperature readings
- Inspect the hose connections and screens
- Verify the cycle temperature after the fix
How to keep HC from coming back
- Match red hoses to the hot inlet and blue hoses to the cold inlet after any move or repair
- Check the labeling on the wall faucets if a plumber has worked nearby
- Tighten hose fittings by hand and look for drips after reconnecting
- Replace old hoses when they harden or crack, particularly where water is hard
Technical reference
- Code
- HC
- Appliance
- Whirlpool washer
- Control family
- Whirlpool Cabrio and WTW top-load HE washers
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool washer error codes
HC questions
Why does HC appear at the end of the cycle?
The washer compares the water temperatures it saw during the cycle. When the hot and cold readings are swapped, it flags this once the cycle completes instead of stopping at the beginning.
Do reversed hoses damage the washer?
Not directly. The washer just washes at the wrong temperatures, so warm and cold cycles can come out too hot or too cold. Fixing the hoses restores the intended results.
How do I tell which wall faucet is hot?
Run a nearby sink's hot tap, then feel the pipe leading to the washer faucet. The warm one is hot. Hoses are color-marked red for hot and blue for cold, but verify by touch.
Will HC clear by itself after I swap the hoses?
It should not appear again once the hoses are on the correct inlets and a full cycle has run. If the code returns, the wall faucets may be plumbed backwards, or the inlet valve readings need testing.
What should I mention when I call about HC?
Tell us which wall faucet you found to be hot, whether the hoses were swapped, and what the wash temperature felt like. That helps us decide between the plumbing and the washer.
Something else going on with your washer?
We trace the cause in your home first and write the price down before any part is swapped.