(813) 565-3059 Book a Repair
Whirlpool washer error code

Whirlpool Washer Display DEN: Store Demo Mode Is On

DEN on a Whirlpool washer says it is in Store Demo Mode, which dealers use on showroom floors; it is not a breakdown and the mode can be switched off.

Normal status, not a failureChecked November 2026

What does Whirlpool washer code DEN mean?

DEN on a Whirlpool washer says the unit is in Store Demo Mode, in guidance that names no series. A dealer switches this mode on so shoppers can watch the washer operate on a showroom floor, and the machine displays its operation while it is on. A washer that left the floor with the mode still on has to be taken out of it before normal use. The code is no breakdown, and the washer is not damaged.

DEN at a glance

Code
DEN
Appliance
Whirlpool washer
Applies to
Whirlpool washers, Store Demo Mode, no series named
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
The washer was put into Store Demo Mode at a dealer

What you may notice with DEN

  • DEN is showing on the display
  • The washer shows lights and cycles without a real wash
  • The Program and Options buttons sit at opposite ends of the panel

How the washer detects DEN

Stores need washers that show how they work without being hooked up to water. To manage that, the control has a Store Demo Mode. While it is on, the washer displays its operation so a shopper can see the buttons, lights and cycles respond, even though no real wash is going on.

DEN is how the display says the mode is active. A person switches it on or off by holding two buttons together for three seconds, with a countdown showing while the hold runs. One button is at the left end of the panel, the other near the right end. If a floor model is delivered with the mode still on, or the two buttons get pressed together by accident, DEN appears. Nothing is damaged. Switching the mode off returns the washer to its normal behavior.

Why DEN appears

  • The washer was put into Store Demo Mode at a dealer
  • Two buttons pressed together by accident, which switched the mode on
  • A showroom washer installed at home with demo mode still active
  • The control otherwise working as designed

Can you keep using the washer with DEN?

Yes, once demo mode is off the washer is ready for normal use. DEN raises no safety concern, and nothing inside the machine is harmed by it. If the washer refuses to run a real cycle after you leave demo mode, something else is going on and the fill and drain circuits should be checked.

What you can safely check

  1. The washer needs no power step; it is doing what it was set to do.
  2. Locate the Program button at the left end of the panel and the Options button near the right end.
  3. Hold both together for three seconds while the countdown runs on the display.
  4. Let go and look for DEN to disappear.
  5. Run a normal cycle to be sure the washer works; if DEN stays after the hold, contact us.

What our technician does for DEN

  • Test the control if DEN stays after a three-second hold
  • Test the fill and drain circuits if the washer will not run a real cycle

How to keep DEN from coming back

  • Avoid pressing the Program and Options buttons together while cleaning the panel.
  • If you buy a floor model, ask for demo mode to be switched off before delivery.

Technical reference

Code
DEN
Appliance
Whirlpool washer
Control family
Whirlpool washers, Store Demo Mode, no series named
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

DEN questions

Is DEN a defect in my washer?

No. The washer is simply in Store Demo Mode, which exists to show shoppers how the machine operates. It is no failure, and switching the mode off returns the washer to normal use.

How is demo mode turned on or off?

Hold Program and Options together for three seconds. A countdown appears while you hold, and the same hold works in both directions.

The washer still will not wash. What does that mean?

Demo mode is not the cause, then. Testing should cover the control along with how the washer fills and drains, and you get the price in writing first.

Can demo mode start by itself?

It does not start on its own. Holding the two buttons together turns it on, which can happen by accident while wiping the panel. Holding them for three seconds again turns it off.

Does a floor-model washer differ in any other way?

Apart from demo mode possibly being left on, the guidance gives no other difference. If the washer misbehaves after DEN is cleared, it deserves a proper test like any other.

Something else going on with your washer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair