(813) 565-3059 Book a Repair
Whirlpool dishwasher error code

Whirlpool Built-In Dishwasher Sanitize Light Flashing: Temperature Missed

On older Whirlpool built-in models such as the WDT750SAHZ, a flashing Sanitize light means the wash fell short of the sanitizing temperature. That means the dishes were not sanitized; it does not mean the dishwasher has stopped working.

Normal status, not a failureChecked November 2026

What does Whirlpool dishwasher code Sanitize Light Flashing mean?

A flashing Sanitize light shows up on older Whirlpool built-ins, the WDT750SAHZ among them, after a cycle in which the sanitizing temperature was missed. It tells you the dishes were not sanitized; it does not say the machine has quit. Household hot water that is too cool when the cycle begins is a common cause, so the tap is the first thing to test. These older dishwashers remain in many homes.

Sanitize Light Flashing at a glance

Code
Sanitize Light Flashing
Appliance
Whirlpool dishwasher
Applies to
Older Whirlpool built-in dishwashers such as the WDT750SAHZ
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
Hot water in the house cooler than the minimum at the start of the cycle

What you may notice with Sanitize Light Flashing

  • The Sanitize light flashes after a cycle finishes
  • Dishes from that cycle were not sanitized
  • Water from the nearest tap is slow to turn hot
  • The older built-in dishwasher otherwise works normally

How the dishwasher detects Sanitize Light Flashing

During a sanitize cycle the control aims for a sanitizing water temperature and reads its temperature sensing to see whether the wash got there. If it did not, the Sanitize light flashes after the cycle. The machine has not stopped working; it is reporting a result.

The tap is the first thing to look at because the dishwasher depends on the household hot water at the start. A water heater set low, or a long pipe run that delays hot water, leaves the first fill cooler than the cycle needs. The dishwasher also heats the water itself, so tap temperature explains only part of what happened. An aging heater or a sensor that reads slightly low can fall just short of sanitizing temperature with no other sign. Reading the wash temperature during a cycle is how those cases are separated.

Why Sanitize Light Flashing appears

  • Hot water in the house cooler than the minimum at the start of the cycle
  • A long pipe run that delays hot water reaching the dishwasher
  • The dishwasher's heater or temperature sensing
  • A reading that only a reset clears

Can you keep using the dishwasher with Sanitize Light Flashing?

Yes. A flashing Sanitize light is not a stop sign, so the dishwasher can keep washing. Rewash dishes from the flagged cycle once the household water runs hot. If the light flashes again after the hot tap runs hot and the control is reset, have us measure the wash temperature and test the heater and sensing.

What you can safely check

  1. Stop the cycle and let hot water run at the closest faucet for about 30 seconds, then verify the temperature is at or above 120 degrees F (49 degrees C), which is the owner's manual minimum.
  2. Reset the control by removing power for one minute, either at the plug or at the breaker if it is hard-wired.
  3. Bring power back and start a sanitize run.
  4. If the flashing returns, call us.

What our technician does for Sanitize Light Flashing

  • Measure the actual temperature reached during the wash.
  • Test the dishwasher's heater.
  • Check the temperature sensing for a reading that falls just short.

How to keep Sanitize Light Flashing from coming back

  • Let the hot tap run at the closest faucet before a sanitize cycle, so the first fill does not start cool.
  • Review the water heater setting if hot water at the faucet never reaches the minimum in the owner's manual.

Technical reference

Code
Sanitize Light Flashing
Appliance
Whirlpool dishwasher
Control family
Older Whirlpool built-in dishwashers such as the WDT750SAHZ
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Sanitize Light Flashing questions

What is the Sanitize light telling me?

That the sanitizing temperature was not reached in the last cycle, so those dishes were not sanitized. Run them again when the water is hot.

What temperature should my household water reach?

Aim for 120 degrees F (49 degrees C) or more, checked by letting the hot tap run about 30 seconds at the nearest faucet. It may be worth reviewing the water heater setting.

Can an aging heater cause the flashing light?

Yes. An aged heater or sensor can come up just short of sanitizing temperature with no other warning. We measure the wash temperature to find out.

Is the flashing Sanitize light the same as a blinking Sani LED?

They describe the same situation on different models: the sanitizing temperature was not reached. The checks start with the household hot water in both cases.

Does the flashing light mean the dishwasher is wearing out?

Not necessarily. Cool household water is a frequent cause, and fixing it clears the warning. If hot water is fine and the light keeps flashing, the heater or sensing deserves testing.

Something else going on with your dishwasher?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair