Whirlpool Vent Hood Display C: Charcoal Filter Reminder
A C on the display of a Whirlpool vent hood while the fan runs is a reminder and not an error: 120 hours of fan use have passed and the charcoal filters need washing.
What does Whirlpool range hood code C mean?
Seeing a C on a Whirlpool vent hood while its fan runs is a reminder and no error. The hood tallies 120 hours of fan operation and then shows the letter to say that the charcoal filters are saturated and due for washing. The motor and control are in no trouble. If your hood vents outdoors and carries no charcoal filter, the reminder can be turned off.
C at a glance
- Code
- C
- Appliance
- Whirlpool range hood
- Applies to
- Whirlpool vent hood with a charcoal filter reminder
- Type
- Maintenance reminder
- Can you clear it yourself?
- Usually, once the care step is done
- Most likely cause
- The charcoal filter has reached its 120-hour mark
What you may notice with C
- A C shows in the display while the fan is running
- The hood still moves air and lights the cooktop
- The charcoal filter has not been washed for a long while
How the range hood detects C
A vent hood with charcoal filters keeps a running tally of how long its fan has worked. Charcoal slowly fills with the odors and grease it catches, so after a set amount of fan time the filters need washing. The control uses the tally as a stand-in for how saturated they have become.
At 120 hours it shows a C while the fan runs. That is the whole message: the filters are due. No sensor, motor or board is involved. Washing and drying restores the filter's ability to work, and holding FAN for 3 seconds tells the control the filter is fresh so that the tally starts again from zero. Hoods that vent outdoors may carry no charcoal filter at all, and for them the reminder is switched off with a separate hold of + and -.
Why C appears
- The charcoal filter has reached its 120-hour mark
- The reminder was left active on a hood that vents outdoors
Can you keep using the range hood with C?
Yes, the hood stays fine to use. The C is a maintenance reminder, and the fan, the light and the control all work normally. A saturated charcoal filter removes less odor, so cooking smells may linger until it is washed. If the hood smells or pulls weakly even after cleaning, the fan and ducting deserve a look.
What you can safely check
- Switch the fan off and let the hood and light cool before you reach for the filter.
- Lift out the charcoal filter and run it through the dishwasher with ordinary detergent on the hottest setting.
- To reactivate it, dry it for 10 minutes in an oven set no hotter than 210°F (100°C), then put it back.
- Keep FAN pressed for 3 seconds and the C goes away.
- On a hood with no charcoal filter, hold the + and - pads together for 3 seconds instead; if the C comes straight back, contact us.
What our technician does for C
- Check how the control counts hours if the C returns right after a reset
- Check the fan and ducting if the hood smells or pulls weakly
How to keep C from coming back
- Wash the charcoal filter whenever the C appears and reset the count straight afterward.
- In a humid Florida kitchen, grease and moisture load filters faster, so notice how the hood smells.
Technical reference
- Code
- C
- Appliance
- Whirlpool range hood
- Control family
- Whirlpool vent hood with a charcoal filter reminder
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool range hood error codes
C questions
What clears the C?
Keeping FAN pressed for 3 seconds makes it disappear and restarts the hour count. Wash the charcoal filter before you do that, so the reset matches a filter that has really been cleaned.
Why does my outdoor-venting hood show a C?
The reminder stays switched on even where no charcoal filter exists. Press + and - together for 3 seconds, an F appears for 3 seconds, and the alarm is then disabled.
Do older hoods carry this reminder too?
Yes, older ones do as well. If it keeps returning at once, the control is worth checking, and we say plainly whether a repair makes sense.
Is the C connected to the F shown by some hoods?
Both are reminders. C belongs to charcoal filters and F to grease filters. Each keeps its own count and has its own reset, and washing one never clears the other.
Does ignoring the C damage the hood?
The hood keeps working, but a saturated charcoal filter removes less odor and cooking smells stay in the room. Washing it is quick and keeps the hood doing its job.
Something else going on with your range hood?
We trace the cause in your home first and write the price down before any part is swapped.