(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Laundry Tower Dryer F2E3: Communication Error Code

F2E3 is a communication error code for the dryer section of a Whirlpool laundry tower. The dryer control and another board in the tower are not exchanging messages correctly.

Needs attention soonChecked November 2026

What does Whirlpool dryer code F2E3 mean?

F2E3 is a communication error code for the dryer section of a Whirlpool laundry tower or stacked laundry center. The dryer control and another board in the tower are not exchanging messages correctly, so the dryer shows the code and may not start. The washer half can keep working, which makes it look as though only part of the tower is affected. The listed approach is a short power reset first, then service if the code remains.

F2E3 at a glance

Code
F2E3
Appliance
Whirlpool dryer
Applies to
Whirlpool laundry tower or stacked laundry center, dryer section
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Connections between the dryer control and the tower's other board

What you may notice with F2E3

  • F2E3 is showing on the dryer section display
  • A dryer that will not start
  • A washer that keeps working normally
  • The code reappearing after a few cycles

How the dryer detects F2E3

A laundry tower stacks a washer and a dryer in one cabinet, and the dryer's control has to exchange messages with another board in that cabinet to run properly. Those messages travel through a wiring harness that runs between the sections. The control sends a request and waits for an answer within a short time.

If the answer does not arrive, or arrives garbled, the control flags a communication error and shows F2E3. The dryer may refuse to start because it cannot confirm its partner board is ready. The problem can sit in the wiring, in either board, or in the interface between them. A reset forces both boards to restart and re-establish contact, which sometimes works, but a link that drops out again after the reset is marginal and has to be tested.

Likely causes of F2E3

  • Connections between the dryer control and the tower's other board
  • The condition of the wiring harness between sections
  • How the control starts back up after a reset
  • Moisture or heat exposure near the control

Can you keep using the dryer with F2E3?

The washer half can keep running, but we advise leaving the dryer off if F2E3 returns after the reset. An unstable control link can end a load without warning, and there is no way to check the connection by running more cycles. If one test cycle after the reset finishes normally, you may use the dryer while you watch it.

What you can safely check

  1. Stop the dryer and disconnect the tower from power for one full minute before touching it.
  2. Plug it in or restore the breaker, then select a timed dry cycle.
  3. Watch the display for a minute to see whether F2E3 comes back.
  4. If it does, stop using the dryer section and schedule service rather than resetting repeatedly.

What our technician does for F2E3

  • Trace the link between the dryer control and the other board
  • Inspect the wiring harness between tower sections
  • Test both boards' response to a restart

How to keep F2E3 from coming back

  • Keep the laundry area dry so moisture does not reach the control
  • Do not stack heavy items on the tower that could press on the cabinet and harness
  • Keep the tower on a grounded outlet with surge protection against Florida lightning

Technical reference

Code
F2E3
Appliance
Whirlpool dryer
Control family
Whirlpool laundry tower or stacked laundry center, dryer section
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F2E3 questions

What does a communication error on my tower mean?

The dryer's control cannot trade messages with another part of the tower. It is a signal path condition, not a statement that the motor or heater is bad, so we trace the link before touching parts.

Will the reset clear F2E3 for good?

Sometimes it does, especially after a brief electrical hiccup. If the code returns within a few cycles, the link is likely marginal and a technician should test it.

Can I still wash while the dryer shows F2E3?

Often yes, since the washer runs on its own cycle. We would not keep using the dryer section until the code is resolved, because an unstable control can interrupt a load.

Is F2E3 the same as F2E2?

They are close relatives. On a tower, both describe communication on the control side, though the wording differs slightly. We run the same checks for each: harness, both boards, and the interface between them.

What happens if I ignore F2E3?

The dryer may keep refusing to start, or may stop partway through loads. The cause does not clear itself, and a loose connection can worsen over time, so having it tested is better than waiting.

Need help with F2E3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair