(813) 565-3059 Book a Repair
Troubleshooting · 4 min read

Whirlpool Electric Coil Range Burner Not Heating: What to Check

Whirlpool Electric Coil Range Burner Not Heating: What to Check

When one burner on a Whirlpool electric coil range will not heat, the coil, the receptacle it plugs into or the switch behind the knob is not delivering power. With the range off and cool, you can swap coils between positions to see whether the coil or the connection has failed, and then decide whether a technician is needed.

Is it the coil or the receptacle?

Switch off the range at the breaker and wait until every burner is cold. Lift the dead coil and look at its terminals. Pitting, blistering or a black burn mark on the metal prongs tells you the coil or its socket has overheated. Plug a working coil of the same size into the dead position and a spare into the working one.

When you restore power and test, if the problem moves with the coil, the coil is worn out. If it stays at the same position, the receptacle, the wiring behind it or the switch is the issue. Never test with the coils pulled halfway out or leaning in the drip pan.

What do a burned receptacle and a loose coil look like?

A burned receptacle shows scorched plastic or ceramic, a discolored screw head or a brittle wire. It often follows months of weak contact that generated heat. A coil that sits loose in its socket arcs and wears the terminals. If the coil wiggles, do not push harder to make it fit. A damaged receptacle is a replacement part, and the wiring that feeds it may also need inspection.

Do not keep cooking on a burner that sparks or smells hot. That kind of heat can damage the range top.

Could the pan be the cause?

A warped pan sits unevenly on a coil and heats poorly, while a pan much smaller than the coil wastes heat. Flat, clean bottoms in a size close to the coil work best. If the burner heats slowly but eventually glows red, the coil is working and the pan may be the issue.

What about the control knob and the switch?

Each burner has an infinite switch behind the knob. A worn switch may give no heat at all, or only certain settings. If the knob turns loosely or the coil glows on every setting, the switch may be involved. Replacing it takes a technician who can test it with a meter. Keep the range off until it is checked if you see a burner stuck on high.

What safety steps matter when I handle coils?

Make sure the range is off at the breaker, not only at the knobs, and that every burner is completely cold. Hot coils hold heat for a long time after they stop glowing. Wear dry hands and keep the drip pans out of the way. Never pull a coil by the wire or force it into the receptacle at an angle. If the terminals are dirty, a dry cloth is enough to wipe them, and sanding or chemical cleaners can damage the contacts.

If you are not comfortable working near the receptacle, stop and call for help. Mistakes here lead to arcing and burns.

How does cleaning affect heating?

Food spilled on a coil burns on, and spills in the drip pan can smoke and spread. Clean the drip pans when they get dark and replace them if they are rusted through or warped. Dirty pans reflect heat poorly and make it hard to tell whether a burner is performing. A clean setup also helps you see damage early, since a scorched receptacle stands out against clean surfaces. Florida humidity speeds corrosion on terminals, so a quick look every few months is worthwhile.

It also helps to know your range. Some Whirlpool coil ranges use plug-in coils of different sizes for each position, and the large rear burner and the small front burner are not interchangeable in every case. Check the size printed on the coil or in the guide before you swap anything, and put each coil back where it belongs. If you cook for a crowd during holidays, a dead burner is a good reason to schedule a repair before the busy week rather than during it.

Sign Likely cause What you can check When to call
One coil stays cold Worn coil, socket or switch Swap coils with the range off Problem stays at the position
Scorched terminals Overheated receptacle Look, do not touch hot parts Right away, stop using the burner
Slow heating with a warped pan Poor contact with the pan Try a flat pan No change
Burner glows on every setting Failed infinite switch Note which knob Soon, use another burner

Frequently asked questions

Can I buy a coil from any store?

Use the type and size listed for your model. A coil with the wrong rating or terminal shape can overheat the socket.

Should I use the oven if a burner is dead?

The oven is a separate circuit, but a burned receptacle can mean heat damage nearby. Keep the range off until it is checked if you smell burning or see scorching.

Why do my coils discolor?

Spills burn onto them and spots turn dark. That is cosmetic. Sparks, a burning smell or uneven heating are more serious signs.

How long do coils last?

It depends on use. Pitting or thin spots mean the coil is wearing out, and replacement is simple and inexpensive.

Sources

Call Book a Repair
Call (813) 565-3059 Book a Repair