Whirlpool Dishwasher F6E4 Error: Float Switch or Out-of-Level Tub
F6E4 on Whirlpool built-in dishwashers such as the WDT750SAHZ points to the water float switch. An out-of-level dishwasher, a stuck float or an interrupted circuit can all bring it up.
What does Whirlpool dishwasher code F6E4 mean?
Whirlpool built-in dishwashers, including the WDT750SAHZ, point to the water float switch as the potential trigger of F6E4. That switch sits in the tub and reports when the water has risen too high. A dishwasher that is not level, a float that sticks, or a broken circuit can make the control raise F6E4 and halt the cycle, so the dishwasher may refuse to run.
F6E4 at a glance
- Code
- F6E4
- Appliance
- Whirlpool dishwasher
- Applies to
- Whirlpool built-in dishwashers such as the WDT750SAHZ
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A dishwasher sitting out of level in its opening
What you may notice with F6E4
- F6E4 shows on the dishwasher display
- The dishwasher refuses to run or stops in the middle of a cycle
- The dishwasher seems tilted or sits unevenly in its opening
How the dishwasher detects F6E4
Inside the tub sits a float switch. As water fills, the float rises with it, and at a set high level the switch tells the control the tub is full enough. The control relies on that signal to stop the fill and to avoid overfilling.
F6E4 is raised when something about that arrangement is wrong. A dishwasher that is out of level can make the water level read wrong. A float that sticks does not rise or fall freely. A broken or loose wire in the switch circuit makes the control lose the signal altogether. In each case the control cannot trust the water level, so it stops the cycle. Leveling is the one cause an owner can check from outside; the float and its wiring need a look inside the dishwasher.
Likely causes of F6E4
- A dishwasher sitting out of level in its opening
- The float and how freely it moves in the tub
- The float switch wiring and its connector
- How the control reads the float circuit
Can you keep using the dishwasher with F6E4?
Not after the code returns. A float that misreads can let the tub take on too much water, so repeated runs risk a spill. Check that the dishwasher is level, reset the power once, and try a cycle. If F6E4 shows again, stop using the dishwasher and have us test the float and its circuit.
What you can safely check
- Stop the cycle, make sure the tub holds no standing water, and unplug the dishwasher or switch its breaker off.
- Check that it sits level in both directions, from front to rear and from side to side, setting a level on the rack rails. Never tilt it while water is inside.
- Restore power after half a minute and close the door.
- Start a cycle.
- If F6E4 comes back, call us.
What our technician does for F6E4
- Inspect the float and test how it moves in the tub.
- Check the float switch wiring and connector.
- Test how the control reads the float circuit.
- Correct the leveling during the same work when the dishwasher is out of level.
How to keep F6E4 from coming back
- After any install or move, set a level on the rack rails to confirm the dishwasher sits flat.
- Keep dropped utensils and other debris out of the tub bottom so nothing interferes with the float.
Technical reference
- Code
- F6E4
- Appliance
- Whirlpool dishwasher
- Control family
- Whirlpool built-in dishwashers such as the WDT750SAHZ
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool dishwasher error codes
F6E4 questions
What does the float switch actually do?
It rides in the tub and signals the control once the water gets too high. If it reports wrongly, the control stops the cycle to avoid overfilling the dishwasher.
Can I fix the leveling myself?
You can check it with a level on the rack rails, but do not tilt the dishwasher with water inside. If the unit needs adjusting in its opening, we handle that during the repair.
Why not keep restarting the dishwasher until F6E4 clears?
A float that is not reporting correctly may let the tub take on too much water. One power reset and a level check are reasonable, and a repeat means the dishwasher needs testing.
Will F6E4 clear on its own?
A one-time reading can clear after a power reset, but a float that sticks or a wire that is loose will bring the code back. If it returns, stop running cycles and have the circuit tested.
What should I tell you about the dishwasher?
Tell us the model, whether it sits level in its opening, and whether F6E4 returns after a power reset. Those details point us at the float, the wiring or the leveling first.
Need help with F6E4?
We trace the cause in your home first and write the price down before any part is swapped.