(813) 565-3059 Book a Repair
Whirlpool dishwasher error code

Whirlpool Portable Dishwasher Clean/Complete Light: Steady or Flashing

On a Whirlpool portable dishwasher, a steady Clean or Complete light at the end of a cycle is normal. A flashing light points to the overfill protection float or the water supply.

Normal status, not a failureChecked November 2026

What does Whirlpool dishwasher code Clean/Complete Light mean?

The Clean or Complete light on a Whirlpool portable dishwasher can carry two messages. Steady at the end of a cycle, it simply says the wash is done. Flashing, it points you at two checks: the float that guards against overfilling, and the water supply. That float must slide freely and the water must be switched on, which matters most just after a new installation.

Clean/Complete Light at a glance

Code
Clean/Complete Light
Appliance
Whirlpool dishwasher
Applies to
Whirlpool portable dishwashers with a Clean or Complete light
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
The overfill protection float stuck in place

What you may notice with Clean/Complete Light

  • The Clean or Complete light glows steadily at the end of the cycle
  • The same light flashes on and off instead
  • The cycle does not run or finish as expected
  • The dishwasher was just connected or moved

How the dishwasher detects Clean/Complete Light

The Clean or Complete light is the dishwasher's end-of-cycle indicator, and it has two behaviors. When it lights steadily after the final step, the control is announcing that the cycle is done. No action is needed.

When it flashes instead, the control is reporting that something kept the cycle from running as planned. The two checks tied to it are the water supply and the float that guards against overfilling. The float rides with the water level and shuts off filling if the water climbs too high; if it sticks, the control cannot read the level properly. The water supply has to be on for the dishwasher to fill, and on a freshly installed portable that is easy to overlook. If the float moves freely and the water is on, attention shifts to the water-level circuit and the control, which a technician tests.

Why Clean/Complete Light appears

  • The overfill protection float stuck in place
  • The dishwasher's water supply switched off
  • A control error that clears after cycling power

Can you keep using the dishwasher with Clean/Complete Light?

Yes when the light is steady, because that is the normal end-of-cycle signal. If it is flashing, do not keep restarting cycles. Free the float, confirm the water is on, and try once. If water leaks or spills at any point, switch the dishwasher off, unplug it and keep it off until it has been inspected.

What you can safely check

  1. Stop the cycle and unplug the dishwasher before you reach for the float or the hoses.
  2. A steady light at the finish of a cycle means nothing is wrong.
  3. If it flashes, check that the overfill protection float slides freely, pressing it down to release it.
  4. Confirm the water supply is turned on.
  5. Plug the dishwasher back in after 30 seconds and start a cycle.
  6. If it still flashes with a free float and the water on, call us.

What our technician does for Clean/Complete Light

  • Test the water-level circuit.
  • Test the control when the float and the water supply check out.
  • Check the sensing tied to the flashing light.

How to keep Clean/Complete Light from coming back

  • After moving or connecting the portable, confirm the water supply is on before the first cycle.
  • Check now and then that the overfill protection float still moves freely.

Technical reference

Code
Clean/Complete Light
Appliance
Whirlpool dishwasher
Control family
Whirlpool portable dishwashers with a Clean or Complete light
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Clean/Complete Light questions

How can I tell whether the light is steady or flashing?

A steady light glows without interruption at the end of a cycle, while a flashing light turns on and off repeatedly. Steady means the cycle finished normally. Flashing means checking the float and the water supply.

Why would the light flash after a new installation?

The water supply may not have been turned on yet, and the float may not be moving freely, so those two are the first things to check before suspecting the control.

Does a flashing light mean the dishwasher will overflow?

Not necessarily, but the float is the overfill protection, so a stuck float deserves attention before another cycle. Free it, then watch the first fill. If water spills, keep the unit unplugged until it is inspected.

Is the Clean or Complete light the same on built-in dishwashers?

Not exactly. On built-ins the Clean light can also flash an F and E error code, which is a separate matter. This page covers the portable model's steady or flashing light, so tell us which type you have.

Will the flashing light go away by itself?

A steady light is only an end-of-cycle signal and needs no fix. A flashing light will keep returning until the cause, such as a stuck float or a closed water supply, is cleared.

Something else going on with your dishwasher?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair