Whirlpool Dishwasher CleanLight Flashing: How to Read the Two-Part Code
Flashes on the Clean light of a Whirlpool built-in dishwasher carry an error code in two parts: the F number first, then the E number. Count both to know which code you have.
What does Whirlpool dishwasher code CleanLight mean?
When the Clean light flashes on a Whirlpool built-in dishwasher, the machine is reporting an error code in two parts. The first run of quick flashes gives the Function number, called F. After a pause of about 1 to 2 seconds comes the second run, the Error number, called E. A longer rest of about 5 seconds then separates one repeat of the sequence from the next.
CleanLight at a glance
- Code
- CleanLight
- Appliance
- Whirlpool dishwasher
- Applies to
- Whirlpool built-in dishwashers that flash codes on the Clean light
- Type
- Low urgency
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- An error code sent out as flashes
What you may notice with CleanLight
- The Clean light flashes in short bursts
- A short gap separates two sets of flashes
- A longer rest comes before the sequence repeats
- The cycle may have stopped partway
How the dishwasher detects CleanLight
Whirlpool built-in dishwashers without a text display use the Clean light as a messenger. The control turns the code into flashes: a Function number, a short pause, then an Error number. Together they form codes such as F7-E1.
The timing keeps the numbers apart. Quick flashes make up each number, a pause of about 1 to 2 seconds separates them, and a longer rest of about 5 seconds comes before the dishwasher starts the sequence again. The light does not say what failed, only which code the control holds. A passing glitch can end after a power reset, while a pattern that comes back tells us which circuit to test. That is why counting carefully is worth the minute it takes.
Likely causes of CleanLight
- An error code sent out as flashes
- A cycle that halted because of the error
- A passing glitch if the flashing ends after a reset
Can you keep using the dishwasher with CleanLight?
That depends on the code you read. Count the flashes first, then cycle the power for 30 seconds and try a cycle. If the light stays off and the dishwasher runs, you can keep using it. If the same numbers return, stop and give them to us for diagnosis. If you see water on the floor or smell something hot, switch the dishwasher off at the breaker and leave it off.
What you can safely check
- Let the dishwasher stop and look for leaks or water on the floor; if you find any, shut off the water supply before anything else.
- Observe the Clean light and tally the first burst of flashes; that is the F number.
- Let the short pause go by, then tally the second burst; that is the E number.
- For example, seven flashes, a pause, one flash, then a repeat is F7-E1.
- Write both numbers down and find that code on our dishwasher list.
- Unplug the dishwasher for 30 seconds, plug it back in and try again. If the same numbers return, call us with them.
What our technician does for CleanLight
- Read the two numbers with you and match them to the code.
- Test the circuit the code points to.
- Work out whether the pattern was a passing glitch or a repeating error.
How to keep CleanLight from coming back
- Write the F and E numbers on a sticky note inside the cabinet door so they are easy to quote later.
- Wait for the longer pause before you start counting so the two numbers are not mixed up.
Technical reference
- Code
- CleanLight
- Appliance
- Whirlpool dishwasher
- Control family
- Whirlpool built-in dishwashers that flash codes on the Clean light
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool dishwasher error codes
CleanLight questions
What is the F number versus the E number?
The F number is the first run of flashes and the E number is the second run after a short pause. Together they name one code. For example, seven flashes, a pause and one flash is F7-E1.
How long is the pause before the code repeats?
Roughly 1 to 2 seconds of quiet separate the two numbers, and a rest of roughly 5 seconds comes before the entire sequence begins again. Waiting for the long pause tells you where a new count begins.
Should I power the dishwasher off between counts?
No, counting needs the light still flashing. Count once or twice first, write the numbers down, and only then cycle power for 30 seconds. If the same pair returns, those numbers are what we need to know.
Is a flashing Clean light always an error?
Not always. Some patterns clear after a power reset, and it is a repeat of the same F and E numbers that points to a real problem. Count the flashes, note the numbers and watch whether they return.
What should I tell you when I call?
Give us the model, the F number and the E number you counted, and whether the pattern came back after a 30-second power cycle. Those numbers let us identify the code before we arrive.
Need help with CleanLight?
We trace the cause in your home first and write the price down before any part is swapped.