(813) 565-3059 Book a Repair
Whirlpool dishwasher error code

Whirlpool Dishwasher 1 Pause 1 Pause Blinks: Reading F1E1 Control Module

One blink, a pause and one more blink on an older Whirlpool built-in dishwasher spells F1E1. Guidance points to the control module, the board that runs the cycles, as the potential cause.

Needs attention soonChecked November 2026

What does Whirlpool dishwasher code 1 Pause 1 Pause mean?

On an older Whirlpool built-in dishwasher, the lights count out F1E1 as a blink, a pause, and another blink. The first count gives the F number and the second gives the E number. In the case of F1E1, the control module is named as the potential cause; it is the electronic board in charge of the cycles. The pattern keeps repeating, and the dishwasher might refuse to start or fail to finish a wash.

1 Pause 1 Pause at a glance

Code
1 Pause 1 Pause
Appliance
Whirlpool dishwasher
Applies to
Older Whirlpool built-in dishwashers with blink-code lights
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The control module, which is the main electronic board

What you may notice with 1 Pause 1 Pause

  • The light blinks once, pauses, then blinks once again
  • The pattern repeats over and over
  • The dishwasher will not start a cycle
  • A cycle stops before the dishwasher finishes

How the dishwasher detects 1 Pause 1 Pause

Older Whirlpool dishwashers without a text display report problems by blinking a light. The count is split in two: the first run of blinks is the F number, and the second run, after a pause, is the E number. One blink, a pause and one blink therefore reads as F1E1.

With F1E1 the potential cause named is the control module. That board runs the cycle sequence, switching the fill valve, pump and other parts on and off at the right moments and checking what comes back. If it is not working properly, it cannot run a cycle with confidence, so the dishwasher stops or never begins, and the lights repeat the pattern until power is reset. A passing electronic error can clear with a reset, while one that returns points to the board or its connections.

Likely causes of 1 Pause 1 Pause

  • The control module, which is the main electronic board
  • A passing electronic error that clears after power is cycled
  • Connections to the control when the pattern keeps returning

Can you keep using the dishwasher with 1 Pause 1 Pause?

Not while the pattern keeps returning. Reset the power one time and try a brief cycle. If the dishwasher runs normally and the blinks stay away, you may keep using it. If the pattern repeats, stop and leave it unplugged, because a cycle the control cannot manage may leave water in the tub. On a hard-wired unit, leave the breaker off.

What you can safely check

  1. Stop the cycle and open the door; make sure your hands are dry and no water stands near the outlet before you handle the plug.
  2. Watch the lights and confirm you see one blink, a pause, then one blink.
  3. Cut power to the dishwasher for 30 seconds by unplugging it, then restore it. For a hard-wired unit, switch its breaker off for the same time instead.
  4. Close the door and run a short cycle.
  5. If the pattern comes back, stop and call us.

What our technician does for 1 Pause 1 Pause

  • Test the control module that runs the cycles.
  • Check the connections feeding the control.
  • Confirm the board is the cause before suggesting a replacement.

How to keep 1 Pause 1 Pause from coming back

  • Keep the control area dry when you wipe the door, since water near the electronics can upset the board.
  • Reset by unplugging only once; repeated resets hide a pattern that needs testing.

Technical reference

Code
1 Pause 1 Pause
Appliance
Whirlpool dishwasher
Control family
Older Whirlpool built-in dishwashers with blink-code lights
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

1 Pause 1 Pause questions

Is one blink, pause, one blink the same as F1E1?

Yes. The blink pattern is the light version of F1E1, with the first count as the F number and the second count as the E number. Both point to the control module as the potential cause.

How long should I leave the dishwasher unplugged?

Leave it without power for 30 seconds, then restore it, much like restarting a computer. A hard-wired unit needs the breaker off for the same 30 seconds. If the blinks return, more resets only delay testing.

What does the control module do?

It is the electronic board that runs the cycles, deciding when the dishwasher fills, washes, drains and finishes. When it misbehaves, the dishwasher may not start or may stop part way through.

Will the blinking go away by itself?

A passing electronic error can clear after a power reset, but a pattern that keeps returning will not disappear on its own. Should it return once power has been off for 30 seconds, the control needs testing.

Is this code related to F1E2?

They share the F1 start, but F1E1 lists the control module while F1E2 describes a main control communication error. Our tests look at the control in both cases, so tell us the exact blink count you see.

Need help with 1 Pause 1 Pause?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair