(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer F3 E3 Code: Inlet Thermistor Reading Out of Range

F3 E3 on Whirlpool WED and WGD dryers names the inlet thermistor. The control is not getting a reading it accepts from the sensor where heated air enters the drum.

Needs attention soonChecked November 2026

What does Whirlpool dryer code F3 E3 mean?

F3 E3 appears on Whirlpool WED and WGD electric and gas dryers, including Cabrio and Duet, and names the inlet thermistor. That sensor sits where heated air enters the drum, and the control relies on it to keep temperatures in range. A reading outside what the control expects triggers the code, and the dryer may stop heating, shut down early, or refuse to begin a cycle. Many owners first notice it as clothes coming out damp.

F3 E3 at a glance

Code
F3 E3
Appliance
Whirlpool dryer
Applies to
Whirlpool WED and WGD electric and gas dryers, Cabrio and Duet
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The inlet thermistor reading and its connector

What you may notice with F3 E3

  • F3 E3 is showing on the dryer display
  • A dryer that tumbles but stops heating the air
  • A cycle that ends early before clothes are dry
  • Laundry that stays damp after a full cycle

How the dryer detects F3 E3

Heat enters a WED or WGD drum through an inlet, and the inlet thermistor sits right there to measure how hot that air is. The control uses that number to decide when to fire the heater and when to ease off, so that the drum stays inside the range for the cycle you picked.

F3 E3 appears when the thermistor's reading falls outside what the control accepts. That can mean the sensor is drifting, its connector is loose, or the wiring has a break. It can also mean the heating circuit is behaving oddly at start-up, so the reading follows a real problem in heat delivery. Poor airflow through the lint screen and vent affects the same reading. Because every one of those produces the same display, the sensor, the wiring, and the heat circuit are tested in turn.

Likely causes of F3 E3

  • The inlet thermistor reading and its connector
  • Wiring from the sensor to the control
  • Heating circuit behavior at start-up
  • Airflow through the lint screen and vent

Can you keep using the dryer with F3 E3?

You may try one cycle after cleaning the lint screen and resetting the breaker. If the dryer heats and finishes normally, keep watching. If F3 E3 returns, stop using the dryer. Running it without a reliable inlet reading lets the heat go unregulated, and repeated cycles only waste power and leave damp loads.

What you can safely check

  1. Stop the cycle, switch the dryer's breaker off, and let it cool before you touch the lint screen.
  2. Pull out and clean the lint screen.
  3. Switch the breaker back on after one minute and start a timed dry cycle.
  4. Stay near the dryer for one minute to make sure F3 E3 does not return.
  5. If it comes back, stop using the dryer and schedule service.

What our technician does for F3 E3

  • Measure the inlet thermistor and inspect its connector
  • Test the heating circuit's behavior at start-up
  • Check the wiring between the sensor and the control

How to keep F3 E3 from coming back

  • Clean the lint screen after every load so heated air moves through the drum freely
  • Keep the vent short and free of kinks, and check the outside hood flap opens
  • Avoid overloading the drum, which restricts the air entering it

Technical reference

Code
F3 E3
Appliance
Whirlpool dryer
Control family
Whirlpool WED and WGD electric and gas dryers, Cabrio and Duet
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F3 E3 questions

What does the inlet thermistor do?

It measures the temperature of air entering the drum so the control can regulate heat. F3 E3 says that measurement looks wrong, which can stop heating or end a cycle early.

Will my clothes still dry with F3 E3?

Often not well. If the dryer stops heating or quits, loads come out damp. Do not keep re-running cycles, since that wastes power while the underlying reading stays unresolved.

Why does a reset sometimes work?

A reset clears a temporary reading error. When the cause is a drifting sensor or a loose connector, the code returns, and then it needs a hands-on test.

Is F3 E3 the same as F3 E1?

They are neighbors, but they name different sensors. F3 E1 is the exhaust thermistor, and F3 E3 is the inlet thermistor. Both sit in the temperature circuit, so we test each sensor and its wiring separately.

What do I need to report about F3 E3?

Give us the model, say that F3 E3 appears with a spaced display, and tell us if clothes come out damp. Also tell us if the lint screen or vent has been a problem, since airflow affects the reading.

Need help with F3 E3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair