(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer Code tS: Thermistor Problem and Vent Checks

The tS code on a Whirlpool dryer points to the thermistor, the temperature sensor, not reading correctly. On vented models a clogged lint screen or restricted vent is the first thing to clear.

Needs attention soonChecked November 2026

What does Whirlpool dryer code tS mean?

On Whirlpool WED and WGD electric and gas dryers, including Cabrio and Duet, tS reports a problem with the thermistor. That is the temperature sensor the control reads, and it is not giving a sensible reading. On a vented, non-heat-pump model, the likely cause is a clogged lint screen or a blocked or restricted vent leading outside. Airflow changes what the sensor sees. You may notice long dry times, a dryer that stops early, or damp clothes at the end of a full cycle.

tS at a glance

Code
tS
Appliance
Whirlpool dryer
Applies to
Whirlpool WED / WGD dryers, Cabrio and Duet
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Lint screen packed with lint

What you may notice with tS

  • Clothes are still damp after a full cycle
  • The dryer stops early or takes much longer
  • The code tS shows on the display
  • Warm, humid air lingers around the vent or laundry room

How the dryer detects tS

Inside the dryer, a thermistor sits in the airstream and changes its electrical resistance as the air gets hotter or cooler. The control reads that resistance many times during a cycle and uses it to decide when to turn heat on, hold it, or end the cycle. It expects the numbers to move in a believable way.

When the reading sits outside what the control accepts, or the sensor circuit seems open or shorted, the control shows tS. On a vented dryer, a blocked lint screen or exhaust slows the air and distorts what the sensor reports, so clean airflow matters as much as the sensor. That is why damp clothes and a dryer that quits early often come with this code.

Likely causes of tS

  • Lint screen packed with lint
  • Vent run crushed, kinked or full of lint
  • Outside exhaust hood clogged
  • Thermistor or its connector reading incorrectly

Can you keep using the dryer with tS?

Stop and check the vent first. A dryer with a restricted vent holds heat and lint inside, which is a fire concern, so do not keep running long cycles with tS showing. Clean the lint screen and look for crushed hose. If a clean vent and a single timed cycle still bring tS back, switch the dryer off at the breaker and have the sensor circuit tested.

What you can safely check

  1. Stop the cycle, unplug the dryer or switch off its breaker, and let the drum cool before reaching inside.
  2. Pull out and clean the lint screen.
  3. Look at the vent hose between the dryer and the wall for crushing, kinks and lint, without pulling the dryer into any strain.
  4. Check that the outside vent opening is clear and its flap moves.
  5. Restore power and run a timed dry cycle. If tS returns, call us.

What our technician does for tS

  • Measure the thermistor with a meter
  • Check its connector and the wiring to the control
  • Inspect the full vent run for restriction
  • Replace the thermistor only if the test shows it is out of range

How to keep tS from coming back

  • Clean the lint screen before you start every single load.
  • Keep the vent hose short, straight and free of kinks behind the dryer.
  • Clear the outside exhaust hood of lint and nests; humid Florida air makes lint pack down faster.

Technical reference

Code
tS
Appliance
Whirlpool dryer
Control family
Whirlpool WED / WGD dryers, Cabrio and Duet
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

tS questions

What does the thermistor do in my dryer?

It is a small temperature sensor that tells the control how hot the air is. When tS appears, those readings do not make sense, so the dryer may stop early or dry poorly.

Can lint alone cause tS?

Yes, it can on vented models. Restricted exhaust changes the temperatures the sensor sees. Clean the lint screen, hose and outside hood first, then run a timed cycle to see whether tS stays away.

Is tS related to hE?

They are close relatives. hE describes a heating error with temperatures too low or too high, while tS points at the thermistor reading itself. Vent checks apply to both, but the technician's tests differ.

Will tS clear by itself after I clean the vent?

It may, if airflow was the whole cause. Run a timed dry cycle after cleaning. If the dryer finishes normally and tS stays gone, the vent was likely the problem; if tS returns, the sensor circuit needs a test.

What should I tell you when I call about tS?

Tell us your dryer family, whether it vents outside or is a HybridCare type, what you cleaned, and whether clothes come out damp. Those details help us choose which tests come first.

Need help with tS?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair