Whirlpool Dryer hE Code: Heating Error, Too Low or Too High
The hE code on Whirlpool WED and WGD dryers describes a heating error where the temperature could be too low or too high. On a vented model, a clogged lint screen or restricted vent is the likely cause.
What does Whirlpool dryer code hE mean?
The hE code on Whirlpool WED / WGD electric and gas dryers, Cabrio and Duet included, describes a heating error, and the temperature could be too low or too high. On a vented, non-heat-pump model, the likely cause is a clogged lint screen or a blocked or restricted vent leading outside the home. Airflow matters a lot for this code. Owners notice long dry times, hot laundry that is still damp, or a dryer that stops with hE on the display.
hE at a glance
- Code
- hE
- Appliance
- Whirlpool dryer
- Applies to
- Whirlpool WED / WGD electric and gas dryers, Cabrio and Duet
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A lint screen and vent run that are blocked or restricted
What you may notice with hE
- hE is showing on the dryer display
- Dry times that have grown much longer than before
- Hot laundry that is still damp at the end
- A dryer cabinet that feels very hot
How the dryer detects hE
A vented dryer heats air, pulls it through the tumbling load, and pushes it out through the lint screen and the vent to the outdoors. The control watches the temperature of that air and cycles the heat on and off to hold it inside a window. Airflow is half of the equation: moving air carries heat out of the drum, and restricted air lets it pile up.
The hE code means the temperature is outside the window, either too low or too high. On a vented model that is not a heat pump, the likely cause is a clogged lint screen or a blocked or restricted vent. A clogged outside hood adds to it. If airflow is fine, the temperature sensing and the heat circuit are tested. Heat pump dryers handle heat differently, so the vent advice applies to vented models only.
Likely causes of hE
- A lint screen and vent run that are blocked or restricted
- An outside exhaust hood clogged with lint
- The temperature sensing and the heat circuit
- The control's response once airflow is restored
Can you keep using the dryer with hE?
Not while hE keeps returning. Clean the lint screen, clear the vent, and try a timed cycle. If the dryer finishes normally, keep watching it. If hE comes back, stop using it. A blocked vent holds heat in the drum and cabinet, which is hard on the dryer and a fire concern, so do not run more loads through it.
What you can safely check
- Stop the cycle, switch the dryer off, and let it cool before you reach for the lint screen.
- Clean the lint screen.
- Check the vent from the dryer to the wall for crushes, kinks and lint.
- Make sure the outside exhaust hood is clear and its flap opens freely.
- Allow ample airflow around the dryer, run a timed dry cycle, and if hE returns, schedule service.
What our technician does for hE
- Measure airflow through the vent run and the outside hood
- Test the temperature sensing and the heat circuit
- Check the control's response once airflow is restored
How to keep hE from coming back
- Clean the lint screen before every load, and wash it now and then to clear film
- Keep the vent to the wall short, straight, and free of crushes and lint
- Clear the outside hood of lint and nesting material, since Florida's long warm season keeps dryers working hard
Technical reference
- Code
- hE
- Appliance
- Whirlpool dryer
- Control family
- Whirlpool WED / WGD electric and gas dryers, Cabrio and Duet
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool dryer error codes
hE questions
Why would a dirty vent cause a heating error?
If hot air cannot leave, temperatures climb, and the control sees them as too high. If air cannot flow properly, it can also see readings as too low. Either way it flags hE.
How do I know if my vent is the problem?
If dry times have grown long and the dryer shell feels hot, suspect the vent. Look for kinks and lint in the run and at the outside hood. We can inspect the whole run.
Does hE affect heat pump models?
The vent advice applies to vented models. Heat pump dryers are handled differently, so if yours is one, tell us the model and we will check the matching circuit.
Does hE mean the heating part has failed?
Not necessarily. The code says the temperature is too low or too high, and a blocked vent can cause either one. We check airflow first, then test the temperature sensing and the heat circuit, before naming any part.
How often should the vent be cleaned?
A good habit is checking the lint screen every load and having the whole vent run inspected when dry times grow longer. A longer vent with more turns collects lint faster, so check it more often.
Need help with hE?
We trace the cause in your home first and write the price down before any part is swapped.