(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer F4E4 Code: Low or No Line Voltage to the Dryer

F4E4 on WED and WGD dryers indicates low or no line voltage, which can keep the heater from turning on. On a laundry tower the dryer section lists it as a main heater condition.

Needs attention soonChecked November 2026

What does Whirlpool dryer code F4E4 mean?

On Whirlpool WED / WGD electric and gas dryers, including Cabrio and Duet, F4E4 indicates low or no line voltage, which means something in the home power supply may be keeping the heater from turning on. An electric dryer needs its own 30-amp circuit with both sides fused. On a Whirlpool laundry tower or stacked laundry center the dryer section lists F4E4 as a main heater condition instead. Expect a dryer that tumbles but does not heat, with the code showing until a key is touched.

F4E4 at a glance

Code
F4E4
Appliance
Whirlpool dryer
Applies to
Whirlpool WED / WGD dryers and laundry tower dryer sections
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The household breaker or fuse feeding the dryer, with one side tripped

What you may notice with F4E4

  • F4E4 stays on the display until a key is touched
  • The drum turns but the air stays cool
  • Clothes that come out damp after a normal cycle
  • One of the two breakers for the dryer is switched off

How the dryer detects F4E4

An electric dryer needs two energized sides of a 240-volt supply, protected by a 30-amp circuit with both sides fused. The drum motor can run on one side, but the heater needs both. The control reads the supply voltage and compares it with what the heater needs. When the voltage looks low or absent, it flags F4E4 and the heater stays off.

That is why the typical result is a dryer that tumbles and does not heat, with the code on the display until you touch a key. The cause may sit in the house, such as a tripped breaker or a blown fuse on one side, or in the cord or outlet connection. On a laundry tower the maker lists F4E4 as a main heater condition instead, so the model type decides which circuit is tested first.

Likely causes of F4E4

  • The household breaker or fuse feeding the dryer, with one side tripped
  • The cord and the outlet connection
  • The main heater circuit on a tower
  • The control's reading of supply voltage

Can you keep using the dryer with F4E4?

If the breakers look fine, reset them once and try a timed cycle. If the dryer heats, keep watching it. If F4E4 returns, stop using the dryer and do not open the cabinet. A supply problem can sit in the outlet or cord, where a loose or overheated connection is a hazard, so have it measured rather than ignored.

What you can safely check

  1. Stop the cycle and switch the dryer off before you look at the breaker panel or the cord.
  2. Touch any pad to clear the code and return to the time remaining.
  3. Check your home breakers for the dryer, since an electric dryer uses two.
  4. Turn the dryer's breaker off for one minute, then on, and start a timed dry cycle for one minute of watching.
  5. If the code returns, call us and do not open the cabinet.

What our technician does for F4E4

  • Measure what voltage reaches the dryer at the outlet
  • Inspect the cord and terminal connection
  • Test the main heater circuit if you have a laundry tower

How to keep F4E4 from coming back

  • Keep the dryer on its own circuit and do not share the outlet with other appliances
  • Check now and then that the cord is seated fully and the plug is not warm
  • Have an electrician look at breakers that trip repeatedly, since Florida summer loads put heavy strain on home circuits

Technical reference

Code
F4E4
Appliance
Whirlpool dryer
Control family
Whirlpool WED / WGD dryers and laundry tower dryer sections
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F4E4 questions

Why would the dryer tumble but not heat?

A 240-volt dryer needs both sides of its supply. If one side is missing, the drum can still turn on the remaining power while the heater cannot work. F4E4 flags that kind of shortage.

Is F4E4 a problem with the dryer or my house?

It can be either. The code says line voltage looks low or absent, so we check the outlet and the breaker side first, then the dryer's own circuit.

Is F4E4 the same on a tower?

No. A laundry tower lists F4E4 for the main heater in the dryer section. The characters match, but the clue differs, so the model type matters when we diagnose it.

Is F4E4 the same as L2?

On a WED or WGD dryer, L2 describes the same low or no line voltage condition. Different generations use different display wording, but the first checks are the same: both breaker sides, the cord, and the outlet.

Can I replace a blown fuse or reset a breaker myself?

Resetting a tripped breaker is a normal owner step. Leave fuse changes, cord work, and anything inside the cabinet or the outlet to an electrician or a technician, because a wrong repair is a safety risk.

Need help with F4E4?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair