(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer Code L2: Low or No Line Voltage at the Dryer

L2 means low or no line voltage and appears on Whirlpool WED and WGD dryers and on HybridCare heat-pump dryers. The home power supply may be keeping the heater from turning on.

Needs attention soonChecked November 2026

What does Whirlpool dryer code L2 mean?

L2 means low or no line voltage and appears on Whirlpool WED / WGD electric and gas dryers, including Cabrio and Duet, and on HybridCare heat-pump dryers. It says there may be a problem with the home power supply that keeps the dryer's heater from turning on, and the dryer keeps running while it shows. On HybridCare dryers the code can appear during the initial installation. Some owners also see F4E4 describe the same condition on a WED / WGD dryer.

L2 at a glance

Code
L2
Appliance
Whirlpool dryer
Applies to
Whirlpool WED / WGD dryers and HybridCare heat-pump dryers
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
The dryer's circuit breaker or fuse, since an electric dryer uses two

What you may notice with L2

  • L2 is showing on the dryer display
  • A drum that turns while the air stays cool
  • Clothes that come out damp after a full cycle
  • One of the two breakers for the dryer is tripped

How the dryer detects L2

An electric dryer is fed by two energized lines, each protected by its own breaker or fuse. The drum motor can run from one line, but the heater needs the full supply to work. The control compares the voltage that arrives with what the heater needs.

When it looks low, or one side is missing, the control posts L2 and the heater stays off. The dryer keeps running, so the drum tumbles while the air stays cool, and the code stays on the display until you touch a pad. The cause is most often outside the dryer: a tripped breaker, a blown fuse, a loose connection at the outlet or terminal, or a cord that was not installed properly. On a HybridCare dryer the code can show up during the initial installation, while the supply or cord connection is still being completed.

Likely causes of L2

  • The dryer's circuit breaker or fuse, since an electric dryer uses two
  • The power cord installation at the dryer
  • The outlet or terminal connection
  • The home wiring feeding the dryer

Can you keep using the dryer with L2?

If you find a tripped breaker, reset it once and try a timed heated cycle. If the dryer heats and L2 stays away, you can keep using it. If L2 returns, stop and have the supply checked. Do not open the cabinet or work on the outlet yourself, since a loose power connection can overheat.

What you can safely check

  1. Stop the dryer and turn it off at its control, then go to the breaker panel and the cord only after it is idle.
  2. Touch any pad to clear the code.
  3. Check whether a household fuse blew or a breaker tripped; electric dryers use two.
  4. Reset the breaker or replace the fuse, and confirm the power cord is installed properly, as the installation instructions describe.
  5. Select a timed dry heated cycle and restart. If L2 stays, call a qualified electrician or us.

What our technician does for L2

  • Measure the voltage reaching the dryer at the outlet or terminal
  • Inspect the cord installation and its connection
  • Test the dryer's own circuit once the supply is confirmed

How to keep L2 from coming back

  • Keep the dryer on its own circuit and do not share the outlet with other appliances
  • Follow the installation instructions for the cord, and check the connection if the dryer is moved
  • Have an electrician check a breaker that trips often, since Florida summer loads strain household circuits

Technical reference

Code
L2
Appliance
Whirlpool dryer
Control family
Whirlpool WED / WGD dryers and HybridCare heat-pump dryers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

L2 questions

Why does the dryer run but not heat with L2?

The drum motor can run on one side of the supply while the heater needs both. L2 warns that voltage looks low or absent for the heater.

Why does L2 show on a new HybridCare dryer?

It can appear during initial installation when the supply or cord connection is not complete. Check the breakers and the cord installation first, and call an electrician if it stays.

Is L2 the same as F4E4?

On a WED / WGD dryer, F4E4 describes the same low or no line voltage condition. Different generations use different display wording, but the first checks are the same.

Can L2 come from my house rather than the dryer?

Yes, and that is the most likely place to look first. A tripped breaker, a blown fuse, or a loose outlet connection can all keep the heater from getting full voltage. We measure what reaches the dryer before we say where the problem is.

Who should fix an electrical supply problem?

A tripped breaker you can reset yourself. Anything involving the outlet, the wiring, or the panel belongs to a qualified electrician. If the measurements show the dryer's own circuit is the cause, we explain what we found and give a written price.

Need help with L2?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair