Whirlpool Dryer PF Code Means a Power Failure Stopped the Cycle
PF on a Whirlpool dryer reports that power was interrupted while a cycle was running. Restarting the cycle or pressing POWER normally clears it, and the dryer is not necessarily broken.
What does Whirlpool dryer code PF mean?
PF stands for power failure. Whirlpool WED and WGD electric and gas dryers, including Cabrio and Duet, show it when the supply dropped out mid-cycle, and HybridCare heat-pump dryers do the same. On WED and WGD models, a noisy supply during an outage can also trigger it, and so can pressing keys in the first 10 seconds after power returns. The dryer itself is usually fine. You can touch and hold START to resume the interrupted cycle, or press POWER to clear the display.
PF at a glance
- Code
- PF
- Appliance
- Whirlpool dryer
- Applies to
- Whirlpool WED / WGD dryers, Cabrio, Duet and HybridCare
- Type
- Normal status, not a failure
- Can you clear it yourself?
- Yes, it is a normal message or setting
- Most likely cause
- A recent outage or brownout interrupted the cycle
What you may notice with PF
- PF replaces the usual cycle information on the display
- The dryer stopped partway and the clothes are damp
- The kitchen or laundry lights flickered or went out earlier
- The dryer would not restart until a key was pressed
How the dryer detects PF
A dryer's control keeps a running record of its cycle and keeps checking the incoming line voltage. If the supply drops out while a cycle is active, the control notes that the run was cut short. When power comes back, it shows PF instead of silently starting over, so you know the load may still be damp.
On WED and WGD models the control can also report PF when the supply is electrically noisy during an outage, because the voltage it reads looks wrong for a moment. Pressing keys during the first 10 seconds after power returns has the same effect, since the control is still settling. Touching and holding START tells it to carry on; pressing POWER tells it to drop the old cycle.
Why PF appears
- A recent outage or brownout interrupted the cycle
- Keys pressed within 10 seconds of power returning
- A noisy supply read by the control as a wrong voltage
- A loose cord or outlet connection
Can you keep using the dryer with PF?
Yes, in most cases the dryer can keep running once PF is cleared. Resume the cycle or start a new one, then check that it completes normally. If the cord feels hot, the plug is loose, or the breaker trips again, stop using the dryer and switch it off at the breaker. A PF that comes back with no outage means the supply or the cord connection needs to be measured before more cycles.
What you can safely check
- Stop the cycle and turn the dryer's breaker off, or unplug it, before you touch the cord or outlet area.
- Switch the breaker back on after one minute and wait about ten seconds before pressing any key.
- Touch and hold START to resume, or press POWER to clear PF.
- Run a short timed dry cycle to confirm normal behavior. If PF returns without any outage, call us.
What our technician does for PF
- Measure the supply voltage at the dryer
- Check the cord and outlet connection for looseness or heat marks
- Inspect the control's power input
- Test a full cycle to see whether PF returns
How to keep PF from coming back
- Wait about ten seconds after power returns before touching any key.
- Keep the plug fully seated and the outlet free of heat marks.
- Florida storms cause short outages and surges, so unplug the dryer during severe weather if you can.
Technical reference
- Code
- PF
- Appliance
- Whirlpool dryer
- Control family
- Whirlpool WED / WGD dryers, Cabrio, Duet and HybridCare
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool dryer error codes
PF questions
Does PF mean my dryer lost its cycle for good?
Not necessarily. PF only reports that power was interrupted. Holding START can resume the cycle where it stopped, and pressing POWER simply clears the message and lets you start fresh.
Why did PF show up when the lights never flickered?
A brief dip or a noisy supply can be too short for you to notice yet still reach the control. Pressing keys during the first 10 seconds after power returns can set it off too.
Does PF appear on HybridCare dryers as well?
Yes. Whirlpool lists PF for WED and WGD dryers as well as HybridCare heat-pump dryers, and the meaning is the same: power was interrupted during a cycle.
Will PF clear without me pressing anything?
No. The message stays until you hold START to resume or press POWER to clear it. The dryer is waiting for your choice because it cannot know whether you want the old cycle back.
What should I tell you if PF keeps returning?
Tell us whether the lights flickered each time, which dryer family you have, and whether the cord or outlet feels warm. That helps us decide whether to start at the supply or the control.
Something else going on with your dryer?
We trace the cause in your home first and write the price down before any part is swapped.