(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer Shows Loc: How to Turn Off Control Lock

Loc on a Whirlpool dryer means the Control Lock is switched on, so the buttons are ignored. It is a feature you can turn off yourself, not a breakdown.

Normal status, not a failureChecked November 2026

What does Whirlpool dryer code Loc mean?

Loc is a message, not a malfunction. Whirlpool WED and WGD electric and gas dryers, including the Cabrio and Duet lines, show it when the Control Lock is active, and so do HybridCare heat-pump dryers. With the lock on, the dryer will not start or run a cycle. HybridCare models may display Lc in place of Loc. On some dryers the lock is its own key, while on others it shares a button with a feature such as Extra Rinse or Steam, so the label on your own panel decides which key to hold.

Loc at a glance

Code
Loc
Appliance
Whirlpool dryer
Applies to
Whirlpool WED / WGD dryers, Cabrio, Duet and HybridCare
Type
Normal status, not a failure
Can you clear it yourself?
Yes, it is a normal message or setting
Most likely cause
Control Lock switched on by a press-and-hold

What you may notice with Loc

  • Pressing Start does nothing and the dryer stays quiet
  • Loc or Lc appears on the display
  • Other keys beep or do not answer
  • The dryer worked normally before the last panel cleaning

How the dryer detects Loc

The dryer's control board watches the keypad for one particular press: the Control Lock key held down. When it sees that hold, it sets a lock state in memory and stops accepting presses from the other keys. Nothing in the drum, motor or heating system is involved, which is why the dryer is otherwise healthy.

The display shows Loc so you know the panel is deliberately ignoring you. Holding the same key for three seconds reverses the state, and the display counts 3-2-1 as it clears. On models where the lock shares a button with Extra Rinse or Steam, the control reads a long hold as lock and a short tap as the other feature, so how long you press matters.

Why Loc appears

  • Control Lock switched on by a press-and-hold
  • Child lock key bumped while cleaning the panel
  • Shared lock key held instead of the other feature
  • Panel buttons sticking after a spill

Can you keep using the dryer with Loc?

Yes. Loc does not affect the dryer's hardware, so there is nothing unsafe about it and nothing to switch off. Turn the lock off by holding the key for three seconds, then use the dryer as normal. If the lock will not release and the display never counts down, leave the dryer alone and have the keypad tested rather than pressing hard on the buttons. Hard presses can damage a panel that is already sticking.

What you can safely check

  1. Stop any cycle and make sure the dryer is empty of anything hot; no power needs to be removed for this check.
  2. Find the Control Lock key on your panel, or the dual-function key your owner's manual names.
  3. Press and hold the key itself for three seconds.
  4. Watch the display count 3-2-1 and then clear.
  5. Press Start to confirm the dryer responds. If Loc stays on after a firm, steady hold, call us so we can test the keypad.

What our technician does for Loc

  • Test the keypad keys for a stuck or worn button
  • Check the panel for moisture or residue from spills
  • Confirm which key carries the lock on your model
  • Quote any panel part only after the test

How to keep Loc from coming back

  • Wipe the panel with a barely damp cloth so spills do not reach the keys.
  • Teach everyone at home which key is the lock, especially on dual-function buttons.
  • Keep a quick press on shared buttons, since a long hold turns the lock on.

Technical reference

Code
Loc
Appliance
Whirlpool dryer
Control family
Whirlpool WED / WGD dryers, Cabrio, Duet and HybridCare
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Loc questions

Is Loc the same as a child lock?

Yes, it is the dryer's way of showing that the Control Lock is on. The panel ignores presses until you turn the lock off, which keeps small hands from starting a cycle.

Why does Loc show on my HybridCare dryer as Lc?

HybridCare heat-pump models may print Lc instead of Loc. Both words describe the same locked state, and both clear the same way, by holding the lock key for three seconds.

Can I run a cycle that already started while Loc is on?

A running cycle can finish, but you cannot change settings. Unlock the controls first if you need to adjust the cycle, pause it, or choose different options.

Will Loc clear by itself?

No. The lock stays on until someone holds the lock key again, and it may remain on after a power cut as well. A normal three-second hold is all it takes to turn it off.

What should I tell you if Loc will not release?

Tell us your dryer's model, whether it is a Cabrio, Duet or HybridCare, and which key you held. Also mention any recent spill on the panel, because that helps us decide what to test first.

Something else going on with your dryer?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair