(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool Built-In Microwave F6 E3: Manager and Converter Control

On Whirlpool built-in microwaves and drawers, F6 E3 concerns two control boards, the appliance manager and the converter, plus the wiring between them, and has nothing to do with a temperature sensor.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F6 E3 mean?

For Whirlpool built-in microwaves and drawers, model WMC50522AS among them, F6 E3 means the control side of the appliance has reported a problem. Whirlpool's wording points at the manager control, the converter control and the wires that join them. Unlike F6 E1 and E2, it has nothing to do with a temperature sensor. The display shows the code, and the cooking functions do not start as usual.

F6 E3 at a glance

Code
F6 E3
Appliance
Whirlpool microwave
Applies to
Whirlpool built-in microwave control boards, WMC50522AS
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Appliance manager control board

What you may notice with F6 E3

  • F6 E3 appears and the cooking functions will not start
  • The microwave does not heat the way it normally would
  • The code may return after a breaker reset

How the microwave detects F6 E3

Two control boards share the work in this part of the appliance: the appliance manager control and the converter control. Wiring and connectors link them, and each expects the other to answer in a set way.

F6 E3 appears when that exchange fails, and the code says nothing about temperature. One board could be misbehaving, a connector could be loose, or a wire could be damaged. The display does not name which. Switching power off and on starts both boards afresh, which clears a stuck reading if that was the cause. When the exchange is healthy the display stays quiet. When it is not, F6 E3 returns, and the converter and manager circuits are tested one at a time.

Likely causes of F6 E3

  • Appliance manager control board
  • Converter control board
  • Connector or wire between the two boards

Can you keep using the microwave with F6 E3?

Not while F6 E3 is showing. The boards that run the appliance are reporting a problem, and the cooking functions will not start properly anyway. One breaker reset is a fair try. Once the display clears and a short cycle goes well, you can carry on and keep watch. If F6 E3 returns, leave the microwave switched off until the control circuits have been tested.

What you can safely check

  1. Leave the microwave idle, then switch its breaker off at the electrical panel.
  2. Leave it off for sixty seconds.
  3. Bring the power back and keep an eye on the display for a further minute.
  4. With the display clear, run a normal cycle and check that the microwave heats and the display looks right.
  5. If F6 E3 returns, leave the unit alone and call us.

What our technician does for F6 E3

  • Check the converter circuit and the manager circuit one at a time
  • Name the responsible part before any repair is approved
  • Check the wiring between the boards

How to keep F6 E3 from coming back

  • Keep the microwave's vents clear and avoid blocking the space around it.
  • In storm season, switching the microwave off at the breaker during close lightning can spare its control boards from surges.

Technical reference

Code
F6 E3
Appliance
Whirlpool microwave
Control family
Whirlpool built-in microwave control boards, WMC50522AS
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

F6 E3 questions

Why is no sensor named for F6 E3?

It is a control board code. Whirlpool names two boards, the appliance manager control and the converter control, plus the wiring that joins them.

Is a breaker reset safe?

Yes. Cutting power at the breaker for a minute and then restoring it is a standard reset. Do not open the unit or handle any wiring; the inside of the cabinet is for a technician.

What follows when F6 E3 keeps coming back?

A repeat tells us the cause is still there. The control circuits are tested one by one, the responsible part is named, and the repair is quoted in writing before any work starts.

Does F6 E3 mean a control board must be replaced?

Not yet. Control boards are costly, so the cause is confirmed first: the manager circuit, the converter circuit and the wiring are tested, and a board is replaced only once it is shown to be the cause.

Is F6 E3 related to the temperature sensor codes?

It sits in the same F6 family, but it names control boards instead of a sensor circuit. The first checks differ from those for the temperature sensor codes.

Need help with F6 E3?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair