(813) 565-3059 Book a Repair
Whirlpool microwave error code

Whirlpool OTR Microwave Code F6E0: Requested Function Not Carried Out

F6E0 means a Whirlpool over-the-range microwave did not carry out the function you requested, with the appliance control board or its wiring named behind it.

Needs attention soonChecked November 2026

What does Whirlpool microwave code F6E0 mean?

Whirlpool's WMH31017HS, WMH32519HZ and WMH53521HZ over-the-range microwaves are among those that can put F6E0 on screen. In plain terms, the oven never did what the pad press asked. The guidance behind the code points at the appliance control board or the wiring serving it. No cycle starts, and F6E0 takes over the display. It marks a circuit to examine, not a board confirmed bad.

F6E0 at a glance

Code
F6E0
Appliance
Whirlpool microwave
Applies to
Whirlpool OTR microwaves: WMH31017HS, WMH32519HZ, WMH53521HZ
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A failing control board behind the keypad

What you may notice with F6E0

  • Pressing a pad does nothing and F6E0 appears instead
  • The display shows F6E0 where the clock normally sits
  • A cycle that ran before now will not begin

How the microwave detects F6E0

On an over-the-range microwave the appliance control board makes the decisions. A press on the keypad sends a signal to the board, and the board then switches the parts that do the work, such as the heating system and the fan.

The control expects those steps to happen in order. If the board cannot finish a request, perhaps because a connection to the keypad or the loads is not carrying a signal, it abandons the cycle and displays F6E0. A power interruption can also leave the board muddled, and then a breaker reset clears the message. If it returns after a reset, the board or its wiring still has a problem that needs testing under power.

Likely causes of F6E0

  • A failing control board behind the keypad
  • Connectors and wires running between the board, the keypad and the loads
  • A control left confused by a power interruption

Can you keep using the microwave with F6E0?

If F6E0 disappears after a breaker reset and the microwave heats normally, you may keep using it while you watch for a return. A repeat is the signal to stop and leave it off. Since the code means a requested function was dropped, the unit might also drop one in the middle of a job, and a microwave over a cooktop should not run unattended in that state.

What you can safely check

  1. Find this microwave's breaker and push it to off before going near the unit.
  2. Let a full minute go by.
  3. Turn the breaker on and remain close for a minute, watching the display for F6E0.
  4. A quiet display means you can retry the function that failed earlier.
  5. If the code comes back, stop using the microwave and contact us.

What our technician does for F6E0

  • Test control board inputs and outputs while powered
  • Follow the wiring between the board, keypad and loads
  • Tell you what was found before any work is approved

How to keep F6E0 from coming back

  • After any outage or flicker, reset the microwave breaker once and check the display before cooking.
  • Wipe the keypad dry after cooking so steam and grease do not collect on it.

Technical reference

Code
F6E0
Appliance
Whirlpool microwave
Control family
Whirlpool OTR microwaves: WMH31017HS, WMH32519HZ, WMH53521HZ
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

Models

Whirlpool models that can show F6E0

Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.

FAQ

F6E0 questions

Which function did the microwave skip?

The code does not say. It records only that a request went unanswered, and the trail leads to the control board or its wiring. Testing both pinpoints the cause.

Does F7 mean the same thing as F6E0?

They are separate codes whose guidance matches, so both lead to the control board and its wiring. The same circuit tests apply, and we name whichever part we find responsible.

May I keep cooking between resets?

Provided a reset clears the message and heating looks normal, you can carry on while watching. A returning message means the control needs testing.

Will F6E0 go away by itself?

Sometimes a power interruption leaves the control in an error state, and a reset clears it for good. If the code returns afterward, the board or its wiring is still reporting a problem and should be tested.

What should I mention on the phone?

Give us the code as it appears, the model number such as WMH31017HS, and which function failed when you pressed the pad. Say whether a reset helped, even briefly.

Need help with F6E0?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair