(813) 565-3059 Book a Repair
Whirlpool range error code

Whirlpool Range Message “Press Cancel to Reset”: Steps to Take

Press Cancel to Reset appears on some Whirlpool ranges when the control detects a problem. Press Cancel first, and if Call Service follows, reset power at the breaker for one minute.

Needs attention soonChecked November 2026

What does Whirlpool range code Press Cancel to Reset mean?

Some Whirlpool freestanding and slide-in ranges, among them the WFE515S0ES and WFG525S0HV, show Press Cancel to Reset after the control notices a problem or error. The message means just what it says. Should Call Service appear once you press Cancel, the next step the guidance gives is a power reset at the breaker. Nothing in the message names a cause, so it works as a prompt first and a diagnosis second.

Press Cancel to Reset at a glance

Code
Press Cancel to Reset
Appliance
Whirlpool range
Applies to
Whirlpool ranges that show a Press Cancel to Reset prompt
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
A one-time control error that Cancel clears

What you may notice with Press Cancel to Reset

  • Press Cancel to Reset scrolls across the display
  • A cycle stops before it finishes
  • Call Service appears after you press Cancel
  • The message returns when you pick the same cycle

How the range detects Press Cancel to Reset

The range control keeps checking the cycle you start, the circuits it uses and the signals coming back. When it detects a problem or error it cannot settle itself, it stops and shows Press Cancel to Reset instead of carrying on with unreliable information. The words are an instruction, not a part name.

Pressing Cancel clears the display and returns the control to its resting state. For a one-time slip, that is all that is needed. If the problem is real, a Call Service message follows, and the guidance then asks for a power reset at the breaker so the control starts fresh. Neither step reveals what was detected, so a message that returns on the same cycle points to a circuit, a sensor reading or wiring that has to be tested.

Likely causes of Press Cancel to Reset

  • A one-time control error that Cancel clears
  • A problem that returns after Cancel and calls for a power reset
  • Control misreading a circuit during a cycle
  • A sensor input or wire that keeps triggering the message

Can you keep using the range with Press Cancel to Reset?

If Cancel clears the message and the oven then runs normally, you may keep cooking while you watch it. If Call Service appears, reset power as described and test with a short bake. A message that keeps coming back on one cycle means that cycle should wait. Do not open panels. If a gas range ever smells of gas, get out first and call the utility from outside.

What you can safely check

  1. Make sure the oven is off and no pan is cooking before you touch the keys.
  2. Press Cancel once.
  3. If Call Service appears, switch the range's breaker off for one minute.
  4. Switch the breaker back on.
  5. Start a bake cycle and watch the oven for a minute to see that the message stays away.
  6. If it returns, note which cycle was running and call us.

What our technician does for Press Cancel to Reset

  • Note which cycle brings the message back and test that circuit
  • Check the control and the wiring or sensor input it reads during that cycle
  • Replace a part only after testing shows it is the source

How to keep Press Cancel to Reset from coming back

  • Enter settings steadily and wait for each step to register before pressing the next key.
  • Note which cycle triggers the message, so a repeat is simple to describe.
  • Keep the keypad clean and dry so stray moisture does not add false presses.

Technical reference

Code
Press Cancel to Reset
Appliance
Whirlpool range
Control family
Whirlpool ranges that show a Press Cancel to Reset prompt
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

Press Cancel to Reset questions

What should I do when Press Cancel to Reset scrolls across the display?

Do as it says and press Cancel. When Call Service follows, cut power at the breaker for a minute, restore it, and start a bake cycle to see whether the message returns. No tools are needed.

Does this message mean the range is unsafe?

The control found a problem, which is not the same as the oven being dangerous, and the message names no part. If it keeps coming back, avoid that cycle and let us find out what the control is responding to.

Will Cancel clear the cause as well?

Cancel only clears the message. It does not tell us what the control detected, so a repeat means the underlying circuit still needs testing.

Is Call Service a different message?

Yes, it is a second message that may follow when you press Cancel. At that stage the guidance asks for a one-minute breaker reset. It still names no part, so repeats call for testing.

Will it clear on its own?

Cancel clears it from the display, and a one-time problem may never return. If it comes back on the same cycle, the control is reading that circuit wrongly, and that needs testing.

Need help with Press Cancel to Reset?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair