(813) 565-3059 Book a Repair
Whirlpool dryer error code

Whirlpool Dryer 0g Error: Power-Down Reset, Then Testing

0g, with a lowercase g, is a Whirlpool WED or WGD dryer code that names no sensor or cause. A breaker reset is the only published step, and a repeat means the control needs testing.

Needs attention soonChecked November 2026

What does Whirlpool dryer code 0g mean?

The code 0g, with a lowercase g, shows on Whirlpool electric and gas dryers of the WED and WGD families, which include Cabrio and Duet generations and models such as the WGD5000DW. The brand gives only a reset routine for it and names no sensor, relay or cause. On the display you see 0g, and the dryer may refuse to start or stop partway. With no published cause, the honest answer is that the dryer has to be tested to find it.

0g at a glance

Code
0g
Appliance
Whirlpool dryer
Applies to
Whirlpool WED and WGD electric and gas dryers
Type
Needs attention soon
Can you clear it yourself?
Sometimes, after the safe checks below
Most likely cause
Control board and its harness connections

What you may notice with 0g

  • 0g with a lowercase g on the display
  • A dryer that refuses to start
  • A cycle that stops partway through
  • The code showing again after a reset

How the dryer detects 0g

Inside the dryer, the control board receives power, reads its sensors and directs the motor and the heat. If one of those signals does not look right, the board stops the cycle and shows a code. For 0g, the brand does not say which signal tripped it.

All that is published is the reset routine: switch the breaker or breakers off for 5 minutes, switch them on again and run a timed cycle. Cutting power wipes a passing glitch, so the dryer may run normally afterward. It cannot explain what caused the code. If 0g returns, the board, its harness connections, the sensor input and the wiring that powers the control all remain possible, and each has to be tested in turn.

Likely causes of 0g

  • Control board and its harness connections
  • A one-time electronic glitch cleared by cutting power
  • Sensor or input circuit feeding the control
  • Wiring where the control receives power

Can you keep using the dryer with 0g?

After one reset you can run a timed cycle and stay nearby. If the dryer starts, heats and finishes without 0g, you can keep using it. If the code appears again, do not keep restarting it, because repeated starts will not change a persistent code. Leave the dryer off until the control and its connections have been tested.

What you can safely check

  1. Stop the dryer and switch off its circuit breaker or breakers, then leave them off for 5 minutes.
  2. Switch them back on.
  3. Run a timed dry cycle.
  4. Stay nearby for a minute to see if 0g appears again.
  5. If it does, do not keep restarting the dryer, and call us.

What our technician does for 0g

  • Test the control board and its harness
  • Check the power feed to the control
  • Trace the sensor input circuit
  • Quote in writing before touching a part

How to keep 0g from coming back

  • Keep the power cord or hard wiring seated firmly and the breaker in good condition
  • Add a surge protector suited to large appliances where storms are frequent
  • Clean the lint screen and vent so the dryer does not run under stress
  • Skip repeated breaker resets as a habit, since they hide what the control saw

Technical reference

Code
0g
Appliance
Whirlpool dryer
Control family
Whirlpool WED and WGD electric and gas dryers
Checked
November 2026

Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.

FAQ

0g questions

Is the lowercase g in 0g important?

Yes. Note it exactly as it displays, 0g. When you call, it helps us to know the exact characters and the dryer model.

Does 0g mean the dryer is overheating?

The brand's guidance does not say, so we confirm on site. It names no heat or sensor cause, only a reset. We would test the dryer to find out instead of assuming a cause.

What does a visit for 0g include?

We test the control, its power feed and the wiring, then explain what we found. The written price comes first, before any part is replaced.

Will 0g clear by itself?

It can, if it was a one-time electronic glitch and the breaker reset cleared it. If it returns later, something real is setting it, and the control and wiring need testing. More resets only delay finding out what happened.

What should I mention about 0g when I call?

Tell us the exact characters, including the lowercase g, the dryer model and whether the dryer is electric or gas. Mention what happened when you reset the breaker. That helps us decide which part of the control path to test first.

Need help with 0g?

We trace the cause in your home first and write the price down before any part is swapped.

Call Book a Repair
Call (813) 565-3059 Book a Repair