Whirlpool Dryer F10 to F24 Codes: Unplug for Half an Hour
F10 through F24 cover a block of codes on Whirlpool WED and WGD dryers. The maker names no part and gives one routine: unplug the dryer for about half an hour, then run a cycle again.
What does Whirlpool dryer code F10 to F24 mean?
The range F10 through F24 covers a block of codes on Whirlpool electric and gas dryers in the WED and WGD series, Cabrio and Duet generations included, such as the WGD5000DW. The maker names no part and gives one routine: turn off and unplug the dryer, wait about half an hour, then plug it in and run a cycle again. Owners see an F-number in this range and the dryer stops. Which circuit the code refers to depends on the exact number shown.
F10 to F24 at a glance
- Code
- F10 to F24
- Appliance
- Whirlpool dryer
- Applies to
- Whirlpool WED and WGD electric and gas dryers, Cabrio and Duet
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A control board reading that clears after a rest
What you may notice with F10 to F24
- An F-number between F10 and F24 on the display
- The dryer stops and ignores the start button
- The dryer runs after a rest, then repeats the code
- The same number shows again within a few cycles
How the dryer detects F10 to F24
The F10 to F24 block is a family of codes that a Whirlpool WED or WGD control raises when one of its circuits reports something it cannot accept. Every number in the range stands for its own circuit, and the control picks the number that matches. It then stops the cycle so nothing runs on a reading it does not trust.
The maker lists no part for any of them. The guidance for the whole range is a single rest: unplug the dryer for about half an hour so the electronics start fresh. A passing electronic error can disappear after that rest. When the same number returns, the dryer is telling us the underlying circuit still disagrees with what the control expects, and the number tells a technician where to begin.
Likely causes of F10 to F24
- A control board reading that clears after a rest
- Connections at the control
- A sensor or drive circuit tied to the exact number
- A passing electronic error
Can you keep using the dryer with F10 to F24?
You can use the dryer again after the half-hour rest if the cycle runs normally. Treat it as a warning, not a cure. If the number returns, stop running loads. Each code in this range points at a real circuit, and a dryer that keeps stopping may leave wet clothes, so it is better to have the circuit tested than to keep restarting.
What you can safely check
- Stop the cycle, switch the dryer off, and unplug it before you do anything else.
- Leave it unplugged for about half an hour.
- Plug it in and start the program or cycle again.
- Write down the exact F-number if the code returns.
- Call us with that number and the model if the failure persists.
What our technician does for F10 to F24
- Read the exact number and identify which circuit it belongs to
- Test that circuit and its connections to the control
- Check the control board's response after a full power rest
How to keep F10 to F24 from coming back
- Plug the dryer straight into its own outlet and keep the cord uncrimped behind the machine
- Keep the lint screen and vent clear so the sensors do not work against blocked airflow
- Use surge protection where storm outages are frequent in Florida
Technical reference
- Code
- F10 to F24
- Appliance
- Whirlpool dryer
- Control family
- Whirlpool WED and WGD electric and gas dryers, Cabrio and Duet
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Related Whirlpool dryer error codes
F10 to F24 questions
Why do I need to wait half an hour?
The routine for F10 to F24 is to unplug the dryer and leave it for about half an hour before plugging it in and running a cycle again.
Do all F10 to F24 codes mean the same thing?
They share one owner routine, but each number points to its own circuit. Please note the exact number so we can prepare before the visit.
What if the code is back right away?
Then the condition is still present. Do not keep restarting. Call us with the number and the model, and we test before suggesting any part.
Which number in the F10 to F24 range do I have?
Read the display exactly and write it down, such as the digits after the F. Each number points to its own circuit, so the exact digits tell us where to look before we arrive.
Can the dryer be harmed by the half-hour rest?
No. Unplugging is the step the maker lists, and it does the dryer no harm. It only restarts the electronics. Keep your hands dry and leave the cabinet closed while it rests.
Need help with F10 to F24?
We trace the cause in your home first and write the price down before any part is swapped.