Whirlpool Over-the-Range Microwave E23: Preheat Took Too Long
A Whirlpool over-the-range microwave shows E23 when its preheat did not reach the target temperature within thirty minutes. The heater, the board or the wires feeding them could be responsible.
What does Whirlpool microwave code E23 mean?
E23 appears on Whirlpool over-the-range microwaves, such as the WMH31017HS, WMH32519HZ and WMH53521HZ, after a preheat that never reaches its target within thirty minutes. Guidance lists the heater, the appliance control board and the wiring as possible causes. What you notice is a preheat running long, then ending with the code. The finding concerns heating start-up, not the keypad.
E23 at a glance
- Code
- E23
- Appliance
- Whirlpool microwave
- Applies to
- Whirlpool over-the-range microwave, e.g. WMH32519HZ
- Type
- Needs attention soon
- Can you clear it yourself?
- Sometimes, after the safe checks below
- Most likely cause
- A heater that has weakened
What you may notice with E23
- A preheat runs very long without the oven getting hot.
- E23 appears in the display when the time limit passes.
- The cooking program ends without heating the food.
How the microwave detects E23
A preheat is a promise the control makes to itself: switch the heating on, and the oven will climb to the target temperature within a set time. The control keeps a clock on that climb. If the target is not reached by thirty minutes, it treats the preheat as failed.
E23 is what you see when that happens. A heater that has weakened, a board that is not switching the heater on properly, or wiring that carries power or sensor signals poorly could each be behind it. The control cannot tell them apart from the outside. So it ends the program and shows E23. Because it points at the start-up of heating, the keypad and display are not suspected, which is why the oven may otherwise look entirely normal.
Likely causes of E23
- A heater that has weakened
- A control board that is not switching the heater on properly
- Wiring that carries power or sensor signals poorly
Can you keep using the microwave with E23?
After a reset, you can try the preheat once more while you watch the oven. If E23 returns, stop using the microwave for heating tasks and switch off the breaker if you smell burning. A heating circuit that cannot reach temperature is not something to push through with repeated restarts, so wait until it has been tested.
What you can safely check
- Stop the cycle; if you smell burning, switch the circuit breaker off and keep the door closed.
- Leave the breaker off for a minute, then restore power.
- Wait nearby for a minute to be sure E23 stays away.
- Begin the same preheat again and check whether heating gets going.
- Leave the vents unblocked and the top of the unit empty. If E23 comes back, call us.
What our technician does for E23
- Test the heating circuit to separate a weak heater from a control that does not switch it on
- Check the control board and its wiring
- Note how the oven heats food as part of the diagnosis
How to keep E23 from coming back
- Leave the airflow openings above and below the microwave unobstructed so heat can leave the cabinet area.
- Avoid stacking items on top of the unit or against the vents, since that restricts airflow.
Technical reference
- Code
- E23
- Appliance
- Whirlpool microwave
- Control family
- Whirlpool over-the-range microwave, e.g. WMH32519HZ
- Maker documentation
- Whirlpool owner manuals and support
- Checked
- November 2026
Code meanings come from the maker’s documentation and our own repair work; we do not reprint the maker’s document. Confirm the full model number before acting on a code. We are an independent repair company, not affiliated with Whirlpool Corporation.
Whirlpool models that can show E23
Models named for this code in Whirlpool documentation that have a page here. Check the full model number on the rating label before you act on a code.
Related Whirlpool microwave error codes
E23 questions
Why does E23 wait so long before it appears?
The control gives the preheat thirty minutes to reach temperature and only then gives up. The code shows once that limit passes, so a long wait before the message is expected.
Which parts does the guidance name for E23?
It points at three areas: the heater, the board that drives it, and the wires between them. The display cannot separate these, so the heating circuit is tested to see whether the heater is weak or the control is not switching it on.
Does E23 mean the whole microwave must be replaced?
Not by itself. The cause may be a single part or connection in the heating circuit. On an older unit, the repair is weighed against replacement and we tell you plainly.
Is E23 the same as a preheat that did not happen correctly?
No. E23 is specifically about not reaching preheat temperature within thirty minutes. A different code covers a preheat that did not start correctly. Each is tested on its own facts.
Does the long preheat cause damage?
The control stops the program at the thirty-minute limit, so the oven does not heat endlessly. Still, repeated long preheats mean the cause is present, so avoid restarting it over and over.
Need help with E23?
We trace the cause in your home first and write the price down before any part is swapped.
